Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Correct any leak found. 1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4" (10.2 cm) clamp. 2. Move dryer into final position. Do not crush or kink vent. Make sure dryer is level. 3. (On gas models) Check to be sure there are no kinks in the flexible gas line. You can change your door swing from a right-side opening to a left-side opening, if desired. Remove the door 1. Place a towel or soft cloth on top of the dryer or work space to protect the surface. 2. Open the dryer door. Remove the 4 screws that hold the door hinge on the front panel of the dryer. Loosen, but do not remove, the screw with the top keyhole opening last (2nd from the top). \ A, Dryer B, Do not remove C. Dryer door 3. Lift and pull forward on the door so that the keyhole clears the screwhead. Remove the door. 4. Lay the dryer door on a flat, protected surface with the inside door assembly facing up. Remove the last screw from Step 1. Remove the 6 screws to release the outer door assembly from the inner door assembly, as indicated below. See illustration. It is important that you remove only the 6 indicated screws. 5. Lift the inner door assembly off of the outer door assembly. Set the outer door assembly aside. Reverse the hinge and hinge cover 1. Place the inner door, screwhead side up, on the work space. 2. Gently pull the plastic cover out and down. This unsnaps the plastic hinge cover from the inside door assembly. 3. Remove the 4 screws that hold the hinge to the door. 4. Move the 2 large hole screw plugs to the opposite side and insert in the original screw holes. A. Hinge screws B. Hole screw plugs 5. Move hinge to the other side and reattach with the 4 screws removed in Step 3. 6. Reverse the plastic cover. Slide it up over the inner door assembly edge and gently snap into place. 7. Set the inner door assembly aside. Reverse the door handle 1. Place the outer door assembly face down on work space. 2. Remove the 2 screws that hold the door handle and the 2 screws holding the hole plugs. If hole plugs do not easily fall out after screws are removed, inser[ a small screwdriver into the holes and gently push the plugs out. A \ /, A. Door handle B. Hole plugs 3. Move the door handle to the other side and reattach with the 2 screws removed from the door handle in Step 2. 4. Move the hole plugs to the new hinge side and attach with the 2 screws removed from the hole plugs in Step 2. Reinstalling the door 1. Check for fingerprints on the glass. Clean if necessary. 2. Place the inner door assembly into the outer door assembly. Align the hinge cover and hinge in the openings on each side. To fit correctly, the inside door assembly edge is completely inside the outside door assembly edge. 3. Reassemble the inner and outer door assemblies with the 6 screws. 4. Use a small flat-blade screwdriver to remove plug strip in the door opening. Slide the head of the screwdriver under the top portion of the plug strip, being careful not to scratch the dryer surface. Lift up. Repeat in the middle and at the bottom. Remove the plug strip in the door opening and insert in the opposite side. 5. Insert a screw in the 2nd opening from the top of the hinge opening and partially tighten. Hang the door by placing the top hinge keyhole over the 2nd screwhead and tighten the screw. By putting this screw in first, the door will hang in place while you insert and tighten the remaining 4 screws. A. Dryer door B, Dryer C. Insert this screw first 6. Close the door and check that it latches securely. 1. Check to be sure all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check to be sure you have all of your tools. 3. Dispose of all packaging materials. 4. Check the dryer's final location. Be sure the vent is not crushed or kinked. 5. Check to be sure the dryer is level. See "Level Dryer." 6. Plug into a grounded 3 prong outlet. Turn power on. 7. Remove the blue protective film on the console and any tape remaining on the dryer. 8. Read "Dryer Use." 9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust. 10. Set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer. If the dryer will not start, check the following: • Dryer is plugged into a grounded 3 prong outlet. • Electrical supply is connected. • House fuse is intact and tight, or circuit breaker has not tripped. • Dryer door is closed. 11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you do not feel heat, turn the dryer off and check to see that the gas supply line shutoff valve is open. • If the gas supply line shutoff valve is closed, open it, then repeat the 5-minute test as outlined above. • If the gas supply line shutoff valve is ...
Dieses Handbuch ist für folgende Modelle:Trockner - ELITE 110.9587 (2.3 mb)