Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Electrolux, modell 134709300

Hersteller: Electrolux
Dateigröße: 2.83 mb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Connection of water inlet hose on Steam Models adds 3/4 in. (2 cm) to installation depth. Upward venting of exhaust on pedestal-mounted or freestandingfloor line floor line dryer mounted on optional pedestal 16.25” (41.5cm) 18.25” (46.5cm) 1.4” (3.5cm) 3.75” (9.5cm) 13.50” (34.5cm) to center of rear vent 3.40” (8.5cm) gas supply pipe on rear of gas unit centerline height for rear vent freestand dryer on floor * To obtain these minimal depth dimensions, dryer must either be vented straight back or with a quick-turn 90° elbow. Connection of water inlet hose on Steam Models adds 3/4 in. (2 cm) to installation depth. Upward venting of exhaust on pedestal-mounted or freestandingfloor line floor line dryer mounted on optional pedestal 9Installation Requirements 38.00” (96.5cm) 53.00” (134.5cm) 50.6” (128.5cm)* to clear open door 31.50” (80cm)* to front of closed door 27.00” (68.5cm) electrical supply on rear of unit dryer adds approximately 4 in. (10.2 cm) to installation depth. Downward venting of exhaust on pedestal-mounted dryer adds approximately 1.7 in. (4.3 cm) to installation depth. 75.75” (192.5cm) 41.00” (104cm) 39.00” (99cm) gas supply pipe on rear of gas unit 50.6” (128.5cm)* to clear open door 31.50” (80cm)* to front of closed door centerline height for rear vent electrical supply on rear of unit * To obtain these minimal depth dimensions, dryer must either be vented straight back or with a quick-turn 90° elbow. Connection of water inlet hose on Steam Models adds 3/4 in. (2 cm) to installation depth. Upward or downward venting of exhaust on stacked dryer adds approximately 4 in. (10.2 cm) to installation depth. 27.00” (68.5cm) Installed dryer dimensions 10 Installation Instructions Electrical installation The following are specific requirements for proper WARNING and safe electrical installation of your dryer. Failure to follow these instructions can create electrical ELECTRICAL SHOCK HAZARD shock and/or a fire hazard. • A U.L.-approved strain relief must be installed onto power cord. If the strain relief is not WARNING attached, the cord can be pulled out of the ELECTRICAL SHOCK HAZARD • This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. • Do not use an extension cord with this dryer. Some extension cords are not designed to withstand the amounts of electrical current this dryer utilizes and can melt, creating electrical shock and/or fire hazard. Locate the dryer within reach of the receptacle for the length power cord to be purchased, allowing some slack in the cord. Refer to the pre-installation requirements in this manual for the proper power cord to be purchased. dryer and can be cut by any movement of the cord, resulting in electrical shock. • Do not use an aluminum wired receptacle with a copper wired power cord and plug (or vice versa). A chemical reaction occurs between copper and aluminum and can cause electrical shorts. The proper wiring and receptacle is a copper wired power cord with a copper wired receptacle. NOTE Dryers operating on 208 volt power supply will have longer drying times than dryers operating on 240 volt power supply. Grounding requirements - Electric dryer (USA) WARNING ELECTRICAL SHOCK HAZARD Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded. For a grounded, cord-connected dryer: 1. The dryer MUST be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical current. 2. After you purchase and install a 3 wire or 4 wire power supply cord having an equipment- grounding conductor and a grounding plug that matches you wiring system, the plug MUST be plugged into an appropriate, copper wired receptacle that is properly installed and grounded in accordance with all local codes and ordinances. If in doubt, call a licensed electrician. DO NOT modify the plug you’ve installed on this appliance. For a permanently connected dryer: 1. The dryer MUST be connected to a grounded metal, permanent wiring system; or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. Installation Instructions 11 Grounding requirements - Electric dryer (Canada) WARNING ELECTRICAL SHOCK HAZARD Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded. For a grounded, cord-connected dryer: 1. The dryer MUST be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical current. 2. Since your dryer is equipped with a power supply ...