Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
MESSAGE light -Turns ON when the TAM is on. Flashes when you have new TAM messages. UP-DOWN (CDS) Buttons (MENU) Button -To access the caller - Press to enter Options Menudisplay records, and to set the Date, Time,Screento scroll through lists Contrast, phone/TAM settings. and options. Ringer light - This flashes when the phone is ringing for an incoming call. M1, M2, M3 one-Touch Memory Buttons (PHONEBOOK) Button -Press to access the Phonebook records. Microphone -For speakerphone use and answering machine OGM & Memo recording. OGM/ (REWIND) Button -Press and hold to record your outgoing messages. Press during message playback to repeat the current message or to go backto the previous message(s). (EXIT)/ (ANSWER ON/OFF) Button - Press to stop recording orplayback. Press and hold to switch the answering maching ON or OFF. With TAM ON is standby mode, press to select OGM1 or OGM2. Important: SPEAKER Volume control -Used to adjust the volume level of the Speakerphone. (REDIAL)/ P (PAUSE) Button -Press to access the LNR lists when in standby mode. Press toinsert a pause when dialing. R (RECALL) Button -You may need this function if your phone is connected to a PBX, or ifyou use BT Calling Features. (MUTE) / STO(Store) Button - Press during a call to mute the microphone or mouthpiece. Press to store the (M1, M2 and M3)one touch memory dialing buttons SPEAKERPHONE Button - Press to make, answer, or end a call using the speakerphone. (PLAY/PAUSE) Button -Press to play back messages and memos. Press to pause playing of a memo or message. MEMO/ (SKIP) Button -Press and hold to record a memo. Press during message playback to skip to the next message. -When the instruction simply say 'press' a button, this means you should press it briefly then release it. -When the instruction say 'press and hold' a button, this means you should keep it pressed until the display changes or you hear a tone. 2 3 The NEW icon only appears when viewing New Caller Display records. entry with 2. Installation 2. Installation 1. Locating the Base unit The Base unit should be placed on a level surface, in a position where: • the mains adapter plug will reach an easily accessible 230-V AC switch mains supply socket -never try to lengthen the mains power cable. • the telephone line cable will reach your telephone line socket or extension socket. • it is not close to a sink, bath or shower, or anywhere else where it might get wet. • it is not close to other electrical equipment - fridges, washing machines, microwave ovens, TVs, fluorescent lights, etc. 2. Plug the coiled handset cord into the Handset. Plug the other end into the jack on the left side of Note: The base unit doesn't require a battery. 3. Place the Handset on the Base unit. 4. Plug the telephone line cord into the PHONE LINE jack at the back of the Base unit. Plug the other end into your telephone line socket 5. Plug the power supply cord the Base unit. Make sure the plugs click into place. into the POWER jack at the back of the Base unit. Plug the other end to a 230V AC, 50Hz mains socket, with the switch on the socket set to OFF 6.Switch ON the mains power atthe socket. Wait while the 7.Lift the Handset and check for Dial tone in the earpiece. The Spirit 710 Base unit must be used only with the supplied mains adapter. Using any other adapter may damage the unit. Always use the telephone line cord supplied with your Spirit 710. Other telephone line cords may not work. or extension socket. display shows INITIALISATION, then the announcement Answering machine on. Announcement one before the display changes to the “ ” standby screen. 4 3. Desk/Wall mount installation 5 To place the Spirit 710 on a desk, connect the stand to the bottom of the phone in the slots near the rear of the base as shown below. Desk Mount Insert the rigid clips of the stand into the slots on the bottom of the phone (nearer the centre of the base). Press down firmly until the flexible clips clicks into place. To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward (3) as shown below. To place the Spirit 710 on a wall, connect the stand to the bottom of the phone in the slots near the front of the base as shown below. Wall Mount Binatone Help Line - 0845 345 9677 Calls are charged at Local Call rate. 6 Desk/Wall mounting continue... Insert the rigid clips of the stand into the slots on the bottom of the phone (nearer the centre of the base). Press down firmly until the flexible clips clicks into place. To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward as shown below. Mark two points on the wall that are 92 mm apart to lay the fixing centers as shown below. BE CAREFUL to check that there are no electrical wires hidden in the wall. Fix two screws (supplied with the unit) at the marked locations, leaving approximately 7mm between the wall and the the screw head. Hang the telephone on the screws using t...