Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Samsung Dateigröße: 4.47 mb Dateiname: Unterrichtssprache:

Grounding wire (green/yellow) 6. Neutral wire (white or center wire) 16_ installing your dryer DV219AGW-02691A_EN.indd 16 2009-01-30 .AEA 6:19:25 6. With a level, check your Dryer and make necessary adjustments to the leveling legs. 7. At this time, make sure all gas connections (on gas models), exhaust and electrical connections are complete. Plug in your Dryer, and check operation by using the checklist below. 8. (GAS MODELS ONLY : DV219AGW) The burner may not ignite initially due to air in the gas line. Allowing your Dryer to operate on a heat setting will purge the line. If the gas does not ignite within 5 minutes, turn your Dryer off and wait 5 minutes. Be sure the gas supply to your Dryer has been turned on. In order to confirm gas ignition, check the exhaust for heat. FINAL INSTALLATION CHECKLIST . Dryer is plugged into electrical outlet and is properly grounded. . Exhaust ductwork is hooked up and joints are taped. . Plastic flexible duct is NOT used. . Used rigid or stiff-walled flexible metal vent material. . Dryer is leveled and is sitting firmly on the floor. . Gas models – gas is turned on with no gas leaks. . Start your dryer to confirm that it runs, heats, and shuts off. 01 installing installing your dryer _17 DV219AGW-02691A_EN.indd 17 2009-01-30 .AEA 6:19:25 installing your dryer DRYER EXHAUST TIPS Plastic or non-metal flexible duct presents a potential fire hazard. WARNING 1. Make sure your dryer is installed properly so it exhausts air easily. 2. Use a 4” diameter rigid metal duct. Tape all joints, including at the dryer. Never use lint-trapping screws. 3. Keep ducts as straight as possible. 4. Clean all old ducts before installing your new dryer. Be sure the vent flap opens and closes freely. Inspect and clean the exhaust system annually. Don’t let a poor exhaust system slow drying by: 1. Restricting your dryer with a poor exhaust system. 12 2. Using a plastic, thin foil, or non-metal flexible duct. 3. Unnecessarily using long ducts that have many elbows. 4. Having crushed or clogged ducts and vent. 3 4 18_ installing your dryer DV219AGW-02691A_EN.indd 18 2009-01-30 .AEA 6:19:27 DOOR REVERSAL 1. Unplug the power cord. 2. Remove two door hinge screws. 3. Lift the door and remove it. 8. Reinsert the black screw in the other hole. 4. Remove a screw on the Frame Front Reinsert the screw (Step 4) on the Frame Front 5. Remove the two screws on the opposite side of the door hinge. 10. Place the door on the other side and reattach it to the dryer. 6. Remove two screws from the holder lever. 11. Reattach the holder lever. 7. Remove one black screw from the door hinge. 12. Reattach the screws in the remaining holes. 01 installing installing your dryer _19 DV219AGW-02691A_EN.indd 19 2009-01-30 .AEA 6:19:29 operating Instructions, tips OVERVIEW OF THE CONTROL PANEL 23645789101 1 Cycle Selector To select a cycle, rotate the Cycle Selector dial to the desired cycle. The indicator light by the cycle name will illuminate. The Normal, Heavy Duty, Perm Press and Delicates cycles are Sensor Dry cycles. Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the selected dryness level (very dry to damp dry) is reached. Normal – Use this cycle to dry loads such as cotton, underwear, and linen. Heavy Duty – Use this cycle to get high heat for heavy fabrics such as jeans, corduroys, or work clothes. Perm Press – Dry wrinkle-free cottons, synthetic fabrics, knits, and permanent press fabrics automatically. The cycle minimizes wrinkling by providing a longer unheated cool-down period at the end of the cycle. Delicates – The Delicates cycle is designed to dry heat-sensitive items at a low drying temperature. Time Dry – Time Dry allows you to select the desired cycle time in minutes. Turn the Cycle Selector dial to Time Dry, then press the Adjust Time up arrow to set the drying time. Press the arrow repeatedly to scroll through the time settings. Wrinkle Release – The Wrinkle Release cycle will release wrinkles from items that are clean, dry, and only slightly wrinkled, such as clothes from a crowded closet, suitcase or items that have been in the dryer too long after the cycle has ended. Wrinkle Release can be used with any temperature selection. Air Fluff – The Air Fluff cycle tumbles the load in room temperature air. Digital Graphic Display The display window shows the estimated time remaining in the cycle after the Start/Pause button is pressed. The estimated time remaining may fluctuate as the cycle progresses. The Drying light will illuminate and remain lit until the cycle is complete. When your dryer is in the cool-down phase, the Cooling light will illuminate. When your dryer is in the wrinkle prevent phase, the Wrinkle Prevent light will illuminate. When the cycle is complete, “END” will appear in the display panel until the dryer door is opened or the Power key is pushed. If your dryer is paused during a cycle, the indicator lights will blink until the Start/Pause button is ...

Herunterladen

Geben Sie zwei Ziffern: