© 2007 Nailer Components And Specifications HD219000 HD289000 • REQUIRES (SCFM with 16 nails 4.1 4.1 per minute @ 90 psi) • AIR INLET 1/4 inch NPT 1/4inch NPT • NAIL LENGTH 2 inch 2 inch RANGE to 31.2 inch to 31.2 inch • NAIL SHANK 0.113 inch to 0.113 inch to RANGE 0.131 inch 0.131 inch • MAGAZINE CAPACITY 60-75 75-105 • WEIGHT 8 lbs. 5 oz. 8 lbs. 15 oz. • LENGTH 19.5 inch 21.75 inch • HEIGHT 15 inch 15 inch • MAX PRESSURE 120 psi 120 psi • PRESSURE RANGE 70 - 120 psi 70 - 120 psi HD349000 4.1 1

Orient a strip of nails with the points down, and drop the strip of nails into the Magazine (part #71). (See Figure C.) 4. Slide the strip of nails forward in the Magazine (part #71). NOTE: The Magazine will hold 60, 10 gauge nails. (See Figure C.) 5. Unlatch the Feeder Shoe (part #52), and allow the Feeder Shoe to slide forward against the strip of nails. (See Figure C.) OPERATION NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 11. 1. Adjust the

10. For more assistance, or to install a complete o-ring set, refer to the breakdown diagram in the back of this manual for component locations. t20568 11.4" brad nailer -11 cleaning & lubrication cleaning use a good solvent to clean the nose assembly of the nailer. always be sure that the nailer is dry before using it again. do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this may result in leaks and damage to the nailer and the air couplings. never

The operator must not hold the trigger pulled on contact trip tools except during fastening operation, as serious injury could result if the trip accidentally contacted someone or something, causing the tool to cycle. Keep hands and body away from the discharge area of the tool. A contact trip tool may bounce from the recoil of driving a fastener and an unwanted second fastener may be driven, possibly causing injury. 3. SEQUENTIAL TRIP OPERATION: The SEQUENTIAL TRIP MODEL contains a contact trip

10401 • Rust resistant chrome finish SAFETY INFORMATION WARNING: Follow all safety warnings listed below and throughout manual. Improper use of this tool can cause severe injury. 1. Read and understand this manual before loading or using tool. 2. Make certain you read and understand all Warnings. 3. Only well-instructed adults should use tool. Never allow children to use tool. 4. Wear safety glasses to protect your eyes. 5. Do not alter this tool in any way. 6. Always store tool with staples rem

Do not use a pneumatic tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating pneumatic tools may result in serious personal injury. · Dress properly. Do not wear loose clothing of jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents often cover moving parts and should be avoided. · Always use the appropriate eye and ear protection and oth

Model No. 12-14NM Features Fastens 12/2, 14/2, 12/3, and 14/3 nonmetallic sheathed cable as well as double-stacked 12/2 and 14/2 nonmetallic sheathed cable to wood framing members Straps will not cut or crush the cables OPERATING INSTRUCTIONS . StrapGun ™ Safety Information WARNING Follow all safety warnings listed below and throughout manual. Improper use of this tool can cause severe injury from flying debris or firing strap into body. 1. Read and understand this manual before loading or using

Never allow children to use tool. 4. When using tool, keep all body parts away from strap exit. 5. Never point tool at anyone. 6. Wear safety glasses to protect your eyes. 7. Lock handle on tool when loading or not in use. 8. Never use this tool where not intended. For example, don’t use tool on concrete, metal, or glass. 9. Do not alter this tool in any way. 10. Always store tool • with straps removed and handle locked • out of children’s reach 11. Keep this manual for reference. It is your gui

ASSEMBLY PROCEDURE FOR SEALS: When repairing a tool, make sure the internal parts are clean and lubricated. Use Parker “O”-LUBE or equivalent on all “O”-rings. Coat each “O”-ring with “O”-LUBE before assembling. Use a small amount of oil on all moving surfaces and pivots. After reassembly add a few drops of BOSTITCH Air Tool Lubricant through the air line fitting before testing. AIR SUPPLY-PRESSURE AND VOLUME: Air volume is as important as air pressure. The air volume supplied to the tool may be