Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Campbell Hausfeld, modell CHN20102

Hersteller: Campbell Hausfeld
Dateigröße: 1.77 mb
Dateiname: c2ec2f0e-b21d-409b-9064-bd5d52100d02.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Do not touch the trigger unless driving fasteners. Never attach air line to tool or carry tool while touching the trigger. The tool could eject a fastener which will result in death or serious personal injury. Also actuate the trigger lock to the safe position when not in use. Always disconnect the tool from the power source when unattended, performing any maintenance or repair, clearing a jam, or moving the tool to a new location. Do not load the tool with fasteners when the trigger is depressed. The tool could eject a fastener causing death or serious personal injury. Always fi t tool with a fi tting or hose coupling on or near the tool in such a manner that all compressed air in the tool is discharged at the time the fi tting or hose coupling is disconnected. Do not use a check valve or any other fi tting which allows air to remain in the tool. Death or serious personal injury could occur. Never place hands or any other body parts in the fastener discharge area of the tool. The tool might eject a fastener and could result in death or serious personal injury. Never carry the tool by the air hose or pull the hose to move the tool or a compressor. Keep hoses away from heat, oil and sharp edges. Replace any hose that is damaged, weak or worn. Personal injury or tool damage could occur. Important Safety Instructions (Continued) ! WARNING 4 Operating Instructions CHN20102 Important Safety Instructions (Continued) Disconnect air supply and release tension from the pusher before attempting to clear jams because fasteners can be ejected from the front of the tool. Personal injury may occur. AIR SOURCE a. Never connect to an air source that is capable of exceeding 200 psi. Over pressurizing the tool is able to result in bursting, abnormal operation, breakage of the tool or serious injury to persons. Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range. b. Never use oxygen, carbon dioxide, combustible gases or any bottled gas as an air source for the tool. Such gases are capable of explosion and serious injury to persons. Do not use any type of reactive gases, including, but not limited to, oxygen and combustible gases, as a power source. Use fi ltered, lubricated, regulated compressed air only. Use of a reactive gas instead of compressed air may cause the tool to explode which will cause death or serious personal injury. Use only a pressure-regulated compressed air source to limit the air pressure supplied to the tool. The regulated pressure must not exceed 110 psi. If the regulator fails, the pressure delivered to the tool must not exceed 200 psi. The tool could explode which will cause death or serious personal injury. SAVE THESE INSTRUCTIONS DO NOT DISCARD Operating Instructions LUBRICATION This tool requires lubrication before using the tool for the first time and before each use. If an inline oiler is used, manual lubrication through the air inlet is not required on a daily basis. The work surface can become damaged by excessive lubrication. Proper lubrication is the owner’s responsibility. Failure to lubricate the tool properly will dramatically shorten the life of the tool and void your warranty. 1. Disconnect the air supply from the tool to add lubricant. 2. Turn the tool so the air inlet is facing up. Place 4-5 drops of 30 W nondetergent oil into air inlet. Do not use detergent oils, oil additives, or air- tool oils. Air tool oils contain solvents which will damage the tool's internal components. 3. After adding oil, run tool briefly. Wipe off any excess oil from the cap exhaust. RECOMMENDED HOOKUP The illustration below shows the recommended hookup for the tool. 1. The air compressor must be able to maintain a minimum of 70 psi when the tool is being used. An inadequate air supply can cause a loss of power and inconsistent driving. 2. An oiler can be used to provide oil circulation through the tool. A filter can be used to remove liquid and solid impurities which can rust or “gum up” internal parts of the tool. 3. Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure from the power source if a regulator fails, or 150 psi, whichever is greater. Use 1/4 inch air hose for runs up to 50 feet. Use 3/8 inch or greater air hoses for 50 foot run or longer. 4. Use a pressure regulator on the compressor, with an operating pressure of 0 - 125 psi. A pressure regulator is required to control the operating pressure of the tool between 70 and 110 psi. OIL O CO2 110 psi 150 psi or greater Recommended Hookup Quick Plug Quick Coupler Air Hose Quick Plug (Optional) Quick Coupler (Optional) Regulator Lubricator Filter 70 psi Min. 110 psi Max. 5 Operating Instructions CHN20102 Operating Instructions (Continued) OPERATIONAL MODE - SI...