Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: DeVillbiss Air Power Company Dateigröße: 745.96 kb Dateiname: Unterrichtssprache:

See specification label on tool for the maximum P.S.I. Unsuitable Cleaning Solvents Flammable vapors in the tool will ignite by a spark and could cause the tool to explode! Never use gasoline or other flammable liquids to clean the tool. PAGE 4 Risk of head injury. HAZARD TO LOOK FOR WHAT COULD HAPPEN HOW TO PREVENT IT Injury to eyes, head and hearing Metal fragments, fasteners, or other material could be projected against head or into eyes resulting in serious injury or property damage. Continued exposure to an operating tool can result in permanent hearing damage. Always wear ANSI approved Z87 safety glasses, Z89.1 head protection and S3.19 hearing protection. Risk of puncture injury. HAZARD TO LOOK FOR WHAT COULD HAPPEN HOW TO PREVENT IT Injury to eyes, head and hearing A fastener could accidentally be driven if the contact trip safety mechanism is not working resulting in serious injury or property damage. If the contact trip bumps something or someone while holding the tool with the trigger depressed, serious injury or property damage could occur. Improper handling can result in damage to the contact trip safety mechanism resulting in unsafe operation. Do not remove, modify or bypass contact safety device. Do not use the tool if any shields or guards are removed or altered. Always check contact trip safety mechanism of the tool before each use. Never carry the tool by the hose or pull the hose to move the tool or a compressor. Keep hoses away from heat, oil and sharp edges. Replace any damaged, weak or worn hoses. Accidental discharge of a fastener can occur, resulting in serious injury or property damage. Hold tool by the handle and keep trigger and contact trip safety mechanism from contacting objects or parts of the body when connecting or disconnecting air supply. Disconnect air hose before loading fasteners, removing a jammed fasteners. PAGE 5 Risk from flying objects. HAZARD TO LOOK FOR WHAT COULD HAPPEN HOW TO PREVENT IT Injury to self or others in the work area. Fasteners could ricochet or be propelled causing serious injury or property damage. When working along edges or next to voids in work surface, the contact trip safety mechanism could be depressed and allow the tool to discharge a fastener into the air or through thin work materials resulting in serious injury or property damage. Pay attention to others in the work area to assure that they are protected from possible accidental discharge of fastener, or projected fragments of work material, fasteners, etc. Provide ANSI approved Z87 safety glasses, Z89.1 head protection, and S3.19 hearing protection to self and others in the work area. Never point discharge of tool at self or others. Do not pull trigger unless tool contact safety device is against work surface. Never attempt to drive fasteners into hard surfaces such as steel, concrete, or tile. Take care to avoid driving a fastener on top of another fastener. Before operating tool, be certain that work surfaces are strong enough and thick enough to contain entire fastener. Position tool carefully so that fasteners will be delivered to the proper location. PAGE 6 LUBRICATION AND MAINTENANCE Do not store the tool in cold weather. Frost or ice can form on the operating valves or mechanisms and the tool may not operate correctly. In cold weather operation (near or below freezing), DO NOT USE a permanent antifreeze such as ethylene glycol for a cold weather lubricant. This type of anitfreeze will damage o-rings and seals of the tool. NOTE Proper lubrication is the owner's responsibility. Failure to lubricate the tool properly will dramatically shorten the life of the tool and void your warranty. Your tool requires lubrication before you use it for the first time and before and after each additional use. If an Oiler is used, manual lubrication through the air inlet is not required on a daily basis. Lubrication prevents wear and prevents rust from forming. 2. Turn the tool so the air inlet is facing up and put one drop of DeVilbiss AC230 Air Tool Oil, high speed spindle oil, such as Unocal RX22, or 3-in-1 oil into the air inlet. DO NOT USE detergent oil or addit...

Herunterladen

Geben Sie zwei Ziffern: