Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
SNC1002x4 Pull feeder shoe back into "locked" position. 6. NF2502X4, NB1252X4, NB2002X4, and SNC1002X4 Replace nose cover and latch into place. NBSNC2X4 Replace nose cover. 7. Reload fasteners into magazine. Refer to Feeder Magazine Latch 5. Using pliers remove fasteners. Loading the Tool section in this manual. PAGE 13 FASTENER JAM INSIDE MAGAZINE: SNC1002x4 Pull feeder shoe back into "locked" position. 1. Disconnect tool from air hose. 2. NF2502X4, NB1252X4, NB2002X4, NBSNC2X4 Release the magazine latch to open the magazine. Feeder 3. Remove jammed fasteners. 4. Reload fasteners into magazine. Refer to Loading the Tool section in this manual. Magazine Latch PAGE 14 TROUBLESHOOTING GUIDE Stop using the Tool immediately if any of the following occur. Serious personal injury could occur. Warranty repairs or replacements must be performed by a DeVilbiss Air Power Authorized Service Center Only. PROBLEM CAUSE SOLUTION Air leaking at trigger valve area. Seals in trigger valve housing are damaged. Seals must be replaced & operation of Contact trip must be checked. On the NBSNC2x4 contact *AWSC for correct part. All other nailers purchase Trigger Repair Kit. Air leaking through the Broken /worn head valve spring. Spring needs to be replaced. Onexhaust deflector. Broken /worn head valve seals. the NBSNC2x4 contact *AWSC for correct part. All other nailers purchase Top Repair Kit. Seals must be replaced. Purchase Top Repair Kit on all nailers. Tool fails to drive fastener. Worn or damaged driver guide. Damaged feed pawl. Worn feed pawl spring. Damaged feed pawl pin. Inadequate air flow or pressure to Tool. Worn seal on piston or lack of lubrication. Damaged seal on trigger valve. Air leaks. Cap seal leaking. Driver guide needs to be replaced. Purchase Driver Blade Kit Replace feed pawl. Contact a *AWSC Replace feed pawl spring. Contact a *AWSC Replace feed pawl pin. Contact a *AWSC Verify air flow or pressure to tool. Replace or lubricate seal. Purchase Bottom Repair Kit Replace seal. Purchase Trigger Repair Kit Screws and fittings need to be tightened. Replace seal. Purchase Top Repair Kit Tool runs slow or has loss of power. Tool not lubricated sufficiently. Inadequate air flow or pressure to tool. Worn seal on piston. Broken spring in cylinder cap. Worn head valve seals. Tools needs to be lubricated. Verify air flow or pressure to tool. Replace seal. Purchase Bottom Repair Kit Spring needs to be replaced.On the NBSNC2x4 contact *AWSC for correct part. All other nailers purchase Top Repair Kit. Replace seals. Contact a *AWSC PAGE 15 TROUBLESHOOTING GUIDE (cont'd) PROBLEM CAUSE SOLUTION Fasteners are jammed in tool. Worn/damaged feed pawl. Worn/damaged feed pawl spring. Fasteners are not correct size. Fasteners are bent. Nail height setting incorrect. Replace feed pawl. Contact an *AWSC Replace feed pawl spring. Fasteners recommended for tool must be used. Replace with undamaged fasteners. Set platform to correct height. Nailer/Stapler misfires or sinks two nails/staples at the same time. Air pressure regulated too high. Trigger action faulty. Adjust air pressure to the correct PSI for that particular model nailer/stapler. Repair trigger action. Purchase a Trigger Repair Kit Air leak near top of tool. Loose exhaust cover screws. O-rings failed on head valve. Tighten screws. Install head valve piston set. Contact an *AWSC Sluggish operation. O-rings blown on head valve. Loose driver guide screws. Install head valve piston set. Contact an *AWSC Tighten screws. Air leak near bottom of tool. Bumper or piston o-rings worn. Replace bumper or piston assembly. Purchase a Bottom Repair Kit Tool does nothing. Air supply inadequate. O-rings failed on head valve piston set. Check PSI and CFM. Install head valve piston set. Contact an *AWSC Poor driver blade return. Dirty cylinder. Worn Bumper. O-rings worn in piston assembly. Disassemble and clean cylinder. Replace bumper. Purchase Bottom Repair Kit Replace piston assembly. On the NBSNC2x4 contact an *AWSC for correct part. All other nailers purchase Bottom Repair Kit. Weak Drive. Inadequate air supply. Worn piston assembly. Check PSI and CFM....
Dieses Handbuch ist für folgende Modelle:Nailers - 2by4 MG-NS2X4A (745.96 kb)
Nailers - 2by4 NB1252X4 (745.96 kb)
Nailers - 2by4 NB2002X4 (745.96 kb)
Nailers - 2by4 NBSNC2X4 (745.96 kb)