Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
The operator and all those persons in the general area should wear safety glasses with permanently attached side shields. Approved safety glasses are imprinted with the characters “Z87.1”. • Always wear appropriate personal hearing and other protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss. • Always engage lock off first then disconnect battery pack from the tool whenever clearing a jam, performing any maintenance or repair, moving the tool or when the tool is unattended. • Do not remove, tamper with, or otherwise cause the tool, trigger, or contact trip to become inoperable. Do not tape or tie trigger or contact trip in the ON position. Do not remove spring from contact trip. Uncontrolled discharge could result. • Do not operate a tool if any portion of the tool, trigger, or contact trip is inoperable, disconnected, altered, or not working properly. Damaged parts or missing parts should be repaired or replaced before use. • Do not alter or modify the tool in any way. • Always assume that the tool contains fasteners. • Do not point the tool at others or yourself at any time. No horseplay! Work safe! Respect the tool as a working implement. • Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. When the tool is not in use, it should be locked in a safe place out of reach of children. • Do not carry the tool from place to place holding the trigger. Accidental discharge could result. • Always use lock-off when tool is not in immediate use. Using the lock-off will prevent accidental discharge. 3 625779-00 BDBN1200Booklet 8/9/04 9:54 AM Page 4 • Use the tool only for its intended use. Do not discharge fasteners into open air, concrete, stone, hardwoods, knots or any material too hard for the fastener to penetrate. Discharged fasteners may cause injury. • Do not use the body of the tool or top cap as a hammer. • Always keep fingers clear of nail track of magazine to prevent injury from inadvertent release of the pusher. • Do not overreach. Maintain proper footing and balance at all times. • Refer to the Maintenance and Service sections for detailed information on the proper maintenance of the tool. • Always operate the tool in a clean, lighted area. Be sure the work surface is clear of any debris and be careful not to lose footing when working in elevated environments such as rooftops. • Do not drive fasteners near edge of material. The workpiece may split causing the fastener to ricochet, injuring you or a bystander. Be aware that the nail may follow the grain of the wood, causing it to protrude unexpectedly from the side of the work material. Drive the chisel point of the nail perpendicular to the grain to reduce risk of injury. • Keep hands and body parts clear of immediate work area. Hold workpiece with clamps when necessary to keep hands and body out of potential harm. Be sure the workpiece is properly secured before pressing the nailer against the material. The contact trip may cause the work material to shift unexpectedly. • Do not use tool in the presence of flammable dust, gases or fumes. The tool may produce a spark that could ignite gases causing a fire. Driving a nail into another nail may also cause a spark. • Keep face and body parts away from back of the tool cap when working in restricted areas. Sudden recoil can result in impact to the body, especially when nailing into hard or dense material. • Do not drive nails onto the heads of other fasteners. Recoil, jammed fasteners, or ricocheted nails may result. • Be aware of material thickness when using the nailer. A protruding nail may cause injury. • Do not actuate the tool unless the tool is placed firmly against the workpiece. • DEPTH ADJUSTMENT: To reduce risk of serious injury from accidental actuation when attempting to adjust depth, ALWAYS; • Engage lock-off. • Remove battery pack. • Avoid contact with trigger during adjustments • Do not drive nails blindly into walls, floors or other work areas. Fasteners driven into live electrical wires, plumbing, or other types of obstructions can result in injury. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber (CCA). Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. • Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear prote...
Dieses Handbuch ist für folgende Modelle:Nailers - 625779-00 (429.24 kb)