Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
2. While doing this step and the next, hold the Nailer pointed away from you and any other people or fragile objects. Pull the Quick Release Lever (49) forward to the position shown in Figure 2. Remove the Driver Guide Cover (51). 3. Remove the jammed nail. Pliers may be necessary to remove a stuck nail. 4. Inspect the Drive Pin (46) for bends or breakage -see location in Figure 3. If it is damaged, do not use the tool until it is repaired by a qualified technician. 5. Lightly oil the Drive Pin (46). Replace the Driver Guide Cover (51) and latch the Quick Release Spring (50) up against both hooks, making sure it is securely in place and the Quick Release Lever (49) is pressed down - see Figure 4. 6. Reload the Nailer. 7. Reconnect the Nailer to the air hose. 8. Press the Safety (56) of the Nailer against an appropriate piece of scrap wood. 9. Test fire the Nailer several times, checking for proper operation. 10. Disconnect the Nailer, remove the nails and store it in a location out of children’s reach. FIGURE 3 Drive Pin (46) (inside housing) FIGURE 2 Driver Guide Cover (51) Quick Release Lever (49) FIGURE 4 Driver Guide Cover (51) hooks -part of Driver Guide (52) Quick Release Spring (50) REV 04/05 SKU 46309 For technical questions, please call 1-800-444-3353. Page 7 Anytime anymaintenance or repairs are done, FIRST: 1. Disconnect the Nailer from the air hose. 2. Empty the Magazine (60) completely. 3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any brads. 4. Always leave the Magazine (60) open during maintenance. The Magazine is spring-loaded and may cause parts or a nail to fly out of the Nailer. Troubleshooting Guide Stop using the Brad Nailer immediately if any of the following problems occur. Repairs and part replacements must be done only by a qualified technician. Allproceduresinboldonthischartaretobeattemptedonlybeaqualifiedtechnician. Problem Likely Cause Solution Air leaking at Trigger area. O-Rings in Trigger Valve housing are damaged. Replace O-Rings and check contact trip operation. Air leaking between Housing and Nose. Loose screws in Housing. Damaged O-Rings/Bumper (17). Tighten screws. Replace O-Rings or Bumper (17). Air leaking at Trigger Valve Stem. O-Rings or Seals are damaged. Replace O-Rings or Seals. Air leaking between Housing and Cap. Loose screws. Damaged Gasket (7). Tighten Screws. Replace Gasket (7). Runs slowly or has power loss. Insufficient oil. Broken Spring in Cylinder Cap. Exhaust (1) is blocked. Lubricate as instructed. Replace Compression Spring (6). Replace damaged parts. Nailer skips a nail. Worn Bumper (17) or damaged Pusher Spring. Dirt in Driver Guide (52). Inadequate airflow to Nailer. Worn or dry O-Ring on Piston. Damaged O-Ring on Trigger Valve. Cap Gasket (7) leaking. Replace Bumper (17) or Pusher Spring. Clean Channels in Driver Guide (52). Check hose and compressor fittings. Replace or lubricate O-Rings. Replace O-Rings. Replace Gasket (7). Nails are jammed. Guide on driver is worn. Nails are wrong size or damaged. Magazine or Nose screws are loose. Drive Pin (46) is damaged. Replace Guide. Use correct, undamaged nails. Tighten screws. Replace Drive Pin (46). Nailer will not drive down tight. Rounded Drive Pin (46) slipping off nail crown. Lack of air pressure. Slow cycling and loss of power. Replace Drive Pin (46). Supply correct pressure (55-95 PSI). Check Compression Spring (6) for broken coils or reduced length. Make sure Exhaust (1) is clear. Blade driving nail too deeply. Worn Bumper (17) and/or Piston Spacer. Replace either or both parts. Allproceduresinboldonthischartaretobeattemptedonlybeaqualifiedtechnician. SKU 46309 For technical questions, please call 1-800-444-3353. Page 8 Parts List Part Description Part Description Part Description 1 Exhaust 24 Trigger Valve Stem 47 Screw 2 Screw 25 O-Ring 48 Cover II 3 Washer 26 Valve Guide 49 Quick Release Lever 4 Cylinder Cap Assembly 27 Releasing Blade 50 Spring 5 Seal Air 28 E-ring 51 Driver Guide Cover 6 Compression Spring 29 Trigger 52 Driver Guide 7 Gasket 30 Spring Pin 53 Screw 8 O-ring 31 Step Pin 54 Spring Pin 9 O-ring 32 Frame 55 Spring 10 Head Valve Piston 33 Spring Pin 56 Safety 11 O-Ring 34 Stopper 57 Screw 12 Stopper 35 Filter Net 58 Retaining Spring 13 Collar 36 O-ring 59 Support 14 O-ring 37 Bottom Cap 60 Magazine 15 O-ring 38 Air Inlet 61 Steel Bar 16 Cylinder 39 Screw 62 Magazine Side Cover 17 Bumper 40 Washer 63 Cover 18 Body 41 Pin 64 Spring 19 Nozzle 42 Spring 65 Spring Pin 20 Cover 43 O-ring 66 Pusher Guide 21 Trigger Axle Head 44 Piston Head 67 Pusher 22 Spring 45 Step Pin 68 Screw 23 O-Ring 46 Drive Pin 69 Hex Nut PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM AND TROUBLESHOOTING GUIDE IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ...