Stimmen - 0, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
. This Quick Reference Guide DOES NOT replace the product’s User Manual. . Make sure to download the latest version of the product’s User Disclaimer Manual from (. You must read ALL the disclaimers and safety notes in this document as well as those in the product’s User Manual before installing, operating, or maintaining this product. Safety Notes . DO NOT open this product unless instructed. It contains no user serviceable parts. . DO NOT look at the light source when this product is on. . DO NOT touch the product when it is operating because it may be hot. . DO NOT cover the ventilation slots when the product is operating to avoid internal overheating. . DO NOT install or operate this product where there is less than 50 cm to the nearest surface to allow adequate ventilation around it. . DO NOT leave any flammable material within 50 cm from this product while operating or connected to the power outlet to minimize the risk of fire. . DO NOT carry this product from the head. Use the handles instead. . DO NOT mount this product overhead without using a safety cable. . DO NOT operate this product outdoors or in any location where dust, excessive heat, water, or humidity may affect it. . DO NOT operate this product if you see damage on the housing, lenses, or cables. In any of these cases, have the damaged parts replaced by an authorized technician at once. . DO NOT connect this product to a dimmer or rheostat. . ONLY connect this product to a grounded and protected circuit. What is . One Q-Wash 260-LED Included . One locking IEC to Edison plug input power cord (US market) . Two hanging brackets . Four M8 bolts (6 mm head) . One safety cable . One custom cut, removable 1° Color Blending Filter . One Warranty Card . One Quick Reference Guide Page 2 of 10 Q-Wash 260-LED QRG Features . Operating modes: 9-channel: Pan, tilt, red, green, blue, color/macros, dimmer, strobe, control 13-channel: Pan, pan fine, tilt, tilt fine, pan/tilt speed, red, green, blue, color/macros, dimmer, strobe, and control . Pan: 540. . Tilt: 270. . RGB static color mixing with or without DMX control . Electronic strobe (1~20 Hz) . Electronic dimmer (0~100%) . High power setting . Remote product reset and vector speed channel . Auto programs . Sound activated programs . 255-step fully customizable program . Recall auto or custom programs via control panel or DMX . Color temperature presets (3,200~10,000 K) . Color calibration . Fan speed control . 3-pin DMX input and output connectors . LCD screen with password protection Product The Q-Wash 260-LED is an RGB LED wash moving head with Description multiple narrow beams. The product consists of a base and a moving head on a yoke. The LEDs are inside ducts, which, along with special optics, provide a very narrow beam angle. Control Panel LCD Front Panel Product Overview Power Input Power Switch DMXIn/OutFuseHolder Rear Panel Page 3 of 10 Q-Wash 260-LED QRG AC Power Fuse Replacement DMX Linking DMX Connection Master/Slave Connection Mounting Product Mounting Diagram This product has an auto-ranging power supply that can work with an input voltage range of 100~240 VAC, 50/60 Hz. 1. Wedge the tip of a flat head screwdriver into the slot of the fuse holder and pry the safety cap out of its housing. It will pull the installed fuse with it. 2. Remove the blown fuse from its safety cap and replace it with a fuse of the exact same type and rating (F 3.15 A, 250 V). 3. Insert the fuse holder back into its place, and reconnect power. The Q-Wash 260-LED can work with a DMX controller using a regular DMX serial connection. If you are not familiar with the DMX standard, please download the DMX Primer document from The Q-Wash 260-LED uses a regular DMX data connection for DMX personalities, BASIC, and ADVANCED. Download the Q-Wash 260-LED User Manual and refer to the Setup chapter to learn how to connect this product for DMX operation, and the Operation chapter to learn in detail how to configure this product for DMX operation. The Q-Wash 260-LED uses the DMX data connection for its Master/Slave mode. Download the Q-Wash 260-LED User Manual and refer to the Setup chapter to learn how to connect this product for Master/Slave operation, and the Operation chapter to learn in detail how to configure this product for Master/Slave operation. Before mounting this product, read the safety notes at the beginning of this guide and on page 2 of the product’s User Manual. Then, follow the mounting procedure indicated in the Setup chapter of the User Manual. Safetycable(included) Cclamps(notincluded) Mountingbrackets(included) OverheadMountingFloorStanding Page 4 of 10 Q-Wash 260-LED QRG Programming For details on how to program this product, please refer to the product’s User Manual. Control Panel Description Button Function