Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
¦ Open the cover. ¦ Clean the detergent drawer and cover under running water and dry. ¦ Close the cover and lock into position. . Insert the cover cylinder onto the guide pin. ¦ Slide in the detergent drawer. Cleaning the drain This is necessary if the washing solution has not been pump completely drained. The pump is blocked by either loose debris or fluff which accumulates if fluff-giving fabrics are washed. Drain the water (Up to 20 litres. Have a suitable container ready.) m Risk of scalding! Allow the hot water to cool down beforehand. Keep children and pets away. ¦ Turn the programme selector to Off. ¦ Open service flap ¦ Carefully unscrew the pump cap - do not remove it completely - and let the water drain out into a shallow container (let the remainder drip onto a floor cloth). Repeat the operation until there is no water left in the machine. ¦ Remove the pump cover. ¦ Remove foreign objects/fluff from inside and clean the interior. The pump impeller wheel must be able to rotate. Clean any residual lye or fluff from the thread of the pump cover and pump housing. ¦ Insert the pump cover and screw tight. ¦ Insert and close the service flap. To prevent unused detergent from flowing into the drain during the next wash cycle: ¦ Pour 1 litre of water into chamber II. ¦ Select the “Spin I” programme. Cleaning water inletstrainers Cleaning the strainer at the water tap Cleaning the strainer on thewashing machine This is necessary if very little or no water flows into the washing machine. First, reduce the water pressure in the inlet hose: ¦ Turn off the tap. ¦ Turn the programme selector to any programme (except Spin I). ¦ Press the “Start Pause A ” button, and allow the programme to run for approx. 40 seconds. ¦ Disconnect the hose fror the water tap. ¦ Rinse the strainer under flowing water. ¦ Connect the hose. ¦ Disconnect the hose fror the back of the washing machine. ¦ Pull out the strainer and rinse under running water. ¦ Insert the strainer and reconnect the hose. ¦ Turn on the water tap and check whether water is still discharged. If water is leaking, check that the filter is correctly seated. ¦ Turn off the tap. Troubleshooting Minor Faults m Risk of electric shock! Repairs may be carried out by customer service or authorised technicians only. If repairs are needed, and assuming that you cannot eliminate the fault yourself with the aid the following table: ¦ Turn the programme selector to Off. ¦ Disconnect the appliance from the mains. ¦ Turn off the tap. ¦ Call customer service, see page 33. Fault Cause Remedial action Washing machine door cannot be opened. Detergent residue in the detergent drawer. Control lights do not come on. Programme does not start. The “Ready '” and “Rinse O” indicator lights flash There is water in the drum. Safety function is active. Damp or lumpy detergent. A fuse has triggered. Power failure. Plug is loose or not plugged in. Loading door not closed properly. “Start Pause A” button not pressed. Select “Spin I” . Wait for 2 minutes. Clean and dry the detergent dispenser; see page 24. Use the dosing aid for liquid detergent. Switch on/replace the fuse. If the fault occurs repeatedly, call Customer Service. An interrupted programme will be resumed when the power returns. If the washing is to be moved,proceed as described under “Cleaning the drain pump”; see from page 25. Check whether laundry is trapped in door. Close the loading door (a click should be heard). Press the “Start Pause A” button. Fault Cause Remedial action Water does not enter the machine or detergent is not washed away. The “Ready '” and “End ?” indicator lights flash. Detergent in chamber I is not washed away. Water not visible in the drum. Washing solution is not completely drained.The “RinseO” and “End ?” indicator lights flash. Water runs out from under the appliance. Foam comes out of the detergent drawer. The washing has not been spun correctly. Spin result unsatisfactory. Spin cycle actuated several times. Tap not turned on. Turn the tap on. Inlet hose kinked or pinched. Filter blocked in water inlet hose. Clean the strainer; see from page 26. A programme without Prewash Select programme with Prewash was selected. “Cottons 90°C T+Prewash ” Not a fault. The water lies below the visible part of the drum. Pumped blocked by foreign objects. Clean the pump (refer to page 25). Fluff-producing laundry was washed. The water drainage pipe or drain hose is blocked. Screw fitting of the inlet hose is leaking. Drainage hose is leaking. Too much detergent or detergent not suitable for use in washing machines used. Large laundry items have become entangled and are not evenly distributed in the drum. For safety reasons, the high-speed final spin cycle was automatically cancelled. Clean drainage pipe and/or drainage hose. Tighten the screw-fitting. Replace the drain hose. Mix 1 tablespoon of fabric softener with .litre of water and pour into chamber II of the detergent dispenser. Reduce detergent dosage for next was...
Dieses Handbuch ist für folgende Modelle:Waschmaschinen - WAG16060MY/02 (1.92 mb)
Waschmaschinen - WAG16060MY/03 (1.92 mb)