Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Beko Dateigröße: 579.02 kb Dateiname: 25ab9bb1-c410-4b3c-8134-0d399bf0551b.pdf Unterrichtssprache:

With the alternative plugs a 13A fuse must be fitted either in the plug or adaptor or in the main fuse box. If in doubt contact a qualified electrician. 8 EN 3 Installation 3 Installation Removing packaging reinforcement Tilt the machine to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon. Opening the transportation locks C Transportation safety bolts must be removed before operating the washing machine! Otherwise, the machine will be damaged! 1. Loosen all the bolts with a spanner until they rotate freely (“C”) 2. Remove transportation safety bolts by turning them gently. 3. Fit the covers (supplied in the bag with the Operation Manual) into the holes on the rear panel. (“P”) C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future. C Never move the appliance without the transportation safety bolts properly fixed in place! Appropriate installation location Install the appliance in environments which have no risk of freezing, in a stable and level position. C The floor must be capable of carrying the load on it! C If the washing machine and a drier are placed on top of each other, their approximate weight together may reach 180 kg when they are full. Important: • Do not place the appliance on top of the power cable. • Keep at least 1cm distance from the edges of other furniture. • Place the machine on a firm surface; do not position it on a long pile rug or such like surfaces. Adjusting the feet C Do not use any tools to loosen the lock nuts. Otherwise, they can be damaged. 1. Manually (by hand) loosen the lock nuts on the feet. 9 EN 2. Adjust them until the machine stands level and firm. 3. Important: Tighten all lock nuts up again. Connecting to the water supply. Important: • The water supply pressure required to run the machine must be 1-10 bar (0,1 – 1 MPa). (Practically, it is necessary to have 10 – 80 liters of water flowing from the tap in one minute to have your machine run smoothly.) Attach a pressure- reducing valve if the water pressure is higher. • Connect the special hose supplied with the machine to the water intake valves on the machine. • In order to prevent water leakage that may occur at the connection points, there are rubber seals (4 seals for the models with double water inlet and 2 seals for other models) attached to the hoses. These seals should be used at the tap and machine connection ends of the hoses. The plain end of the hose fitted with a filter must be attached to the tap and the elbowed end must be attached to the machine. Tighten the nuts of the hose well by hand; never use wrenches to tighten the nuts. • Open the taps completely after making the hose connection to check if there is any water leakage at the connection points. Turn off the tap and remove the nut in case of any leakage. Retighten the nut carefully after checking the seal. To prevent any water leakage and any other damage to be caused by it, keep the taps closed when the machine is not in use. • Models with a single water inlet should not be connected to the hot water tap. Laundry may be damaged or the appliance may switch to protection mode and not work. When returning the appliance to its place after maintenance or cleaning, care should be taken not to fold, squeeze or block the hoses. Connecting to the drain The water discharge hose can be attached to the edge of a washbasin or waste water system. The drain hose should be firmly fitted into the drain as to not loosen in its housing. Important: • The end of the drain hose can be directly connected to the wastewater drain or to the washbasin. The fitting must be secured in all types of connections. 10 EN Your house may be flooded if the hose falls out of its housing during water discharging. • The hose should be attached to a height of at least 40 cm, and 100 cm at most. • In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out wet. Therefore, the heights described in the figure should be followed. • To prevent dirty water refilling the machine, and to allow for easy discharge, the end of the hose must not be submerged in the drain water. The end of the hose must be able to take in air. The hose should be pushed into the drainage for more than 15 cm. If it is too long you may have it shortened. • The end of the hose should not be bent, it should not be stepped on and it must not be folded between the drain and the machine. • The length of the hose is too short, you may add an extension hose to the original section. The length of the hose must not be longer than 3.2 m after coming out of the machine. To avoid water leakage failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak. Electrical connection Connect the mac...

Herunterladen

Geben Sie zwei Ziffern: