Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
This can be measured with a manometer placed on the exhaust duct approximately two feet (61 cm) from the dryer. Refer to Figure 38. All dryers connected to the main collector duct should be in operation when pressure is checked. Installing an exhaust system does not eliminate the necessity of cleaning the dryer lint filter before each load. The dryer interior and the complete exhaust system should be cleaned periodically by a qualified service person to remove any lint build-up. A Backdraft Damper, Part No. 58786 (obtain locally), should be installed in a 4 inch (10.2 cm) diameter VERTICAL duct system only. This will prevent a backdraft when dryer is not in use, and will keep the exhaust air in balance within the central exhaust system. 46 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 801539 Installation 30 NOTE: Where the exhaust duct pierces a combustible wall or ceiling, the opening must be sized per local codes. Wall EXHAUST AIR FLOW MAXIMUM LENGTH OF DUCT 30 feet (9.1 m) HORIZONTAL EXHAUST INSTALLATION 3 EXHAUST OUTLET 2 in. (5 cm) Minimum or Clearance per Local Codes 4 No Screen or Cap 5 Clean Out Cover - Inspect Monthly 1 5 4 1 2 Figure 40 VERTICAL EXHAUST INSTALLATION H319I 1 No Screen or Cap 2 Roof 3 Wall 4 2 in. (5 cm) Minimum or Clearance Per Local Codes 5 NOTE: Where the exhaust duct pierces a combustible wall or ceiling, an opening must be sized as shown or per local codes. A WARNING To reduce the risk of fire and the accumulation of combustion gases, DO NOT exhaust dryer air into a window well, gas vent, chimney or enclosed, unventilated area, such as an attic, wall, ceiling, crawl space under a building or concealed space of a building. Figure 41 Duct Station Minimum Diameter of Collector Duct A 4 inches (10.2 cm) B 8 inches (20.3 cm) C 9 inches (22.9 cm) D 10 inches (25.4 cm) E 11 inches (27.9 cm) F 12 inches (30.5 cm) G 13 inches (32.6 cm) H 14 inches (35.6 cm) I 15 inches (38.1 cm) J 15 inches (38.1 cm) K 16 inches (40.6 cm) 4 801539 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 47 Installation Lint Filter CLEAN THE LINT FILTER BEFORE DRYING EACH LOAD. (Refer to Figure 42 for lint filter location.) Cleaning the lint filter is important because a layer or pad of lint on the filter will block the flow of air through the dryer, thus reducing the efficiency of the dryer. The clothes will take longer to dry and energy will be wasted. Dryer Motor Overload Protector The motor overload protector stops the motor in the event of an overload. After cooling, the overload protector will reset itself. The dryer can be restarted by pressing the START keypad. If the overload protector cycles again, remove the unit from use and call the service person to correct the problem. Figure 42 48 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 801539 Operation Operation Instructions for MDC Washers IMPORTANT: Prior to first wash, use an allpurpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside of washer drum. IMPORTANT: Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation. Step 1: Load Laundry Load items loosely into wash drum. Step 2: Close Loading Door Close loading door tightly. The washer will not operate with the loading door open. Figure 43 801539 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 49 Operation Step 3: Add Laundry Supplies Open dispenser drawer. Measure and add low sudsing detergent (1), bleach (2) and fabric softener (3) to the dispenser drawer. Refer to Figure 45. Close dispenser drawer. IMPORTANT: If using detergents made for topload washers, avoid oversudsing by using 1/2 of the recommended amount. A CAUTION Dispenser drawer requires a special tool removal. Contact a service person if removal is necessary. for W236 3 2 1 SWD753N 1 Detergent 2 Bleach 3 Fabric Softener Figure 45 Step 4: Determine Proper Controls for Washer The direction of the arrow indicates which controls are for the washer. DRY1930N Figure 46 Step 5: Set Fabric Selector and Wash Temperature Push keypad for NORMAL/HOT, NORMAL/ WARM, PERM PRESS/WARM or DELICATES/ COLD cycle. Light indicates selection. NOTE: Changes can be made to Fabric Selector setting up until the first fill is complete. 50 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 801539 Operation Step 6: Insert Coin(s) or Card To Insert Money Insert coin(s) in coin slot. Check pricing as seen on digital display. W387I Figure 48 To Insert Card Insert card into opening. Figure 49 Step 7: Start Washer After vend price has been satisfied, push the START keypad. DOOR MUST BE CLOSED TO START WASHER. 801539 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 51 Operation Indicator Lights WASH WASH is lit at the beginning of a Wash cycle and...