Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Excessive laundry load. • Reduce the laundry load. What to do if... 37 Problem Cause possible/Solution The door will not open: The machine vibrates or is noisy: The programme is still running. • Wait until the end of washing cycle. The door lock has not been released. • Wait until the DOOR symbol disappears. There is water in the drum. • Select drain or spin programme to empty out the water. The transit bolts and packing have not been removed. • Check the correct installation of the appliance. The support feet have not been adjusted • Check the correct levelling of the appliance. The laundry is not evenly distributed in the drum. • Redistribute the laundry. Maybe there is very little laundry in the drum. • Load more laundry. Spinning starts late or the machine does not spin: The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume. If, after some minutes, the laundry is still not evenly distributed in the drum, the machine will not spin. • Redistribute the laundry. The machine is fitted with a type of motor which makes a different noise compared with other The machine makes an unusual traditional motors. This new motor ensures a softer noise start and more even distribution of the laundry in the drum when spinning, as well as increased stability of the machine. Machines based on modern technology operate very No water is visible in the drum: economically using very little water without affecting performance. Anti-flooding system has activated. The display shows the alarm code • Disconnect the appliance and contact the Service EF0: :: Force Centre 38 What to do if... If you are unable to identify or solve the problem, contact our service centre. Before telephoning, make a note of the model, serial number and purchase date of your machine: the Service Centre will require this information. Technical Data Dimensions Width Height Depth (door included) 60 cm 85 cm 63 cm Power supply voltage/frequency 230-240 V/50 Hz Electrical connection Total power absorbed 2050 W Minimum fuse protection 10 A Water supply pressure Maximum Load Spin Speed Minimum Maximum Cottons Maximum 0,05 MPa 0,80 MPa 7 kg 1400 rpm Consumption value 39 Consumption value Programme Water consumption (lltres) Energy consumption (KWh) Programme duration (Minutes) White Cottons 95° or 90° 62 2.1 Cottons 60° 58 1.35 (*)Cotton ECO 60° 52 1.19 Cottons 40° 58 0.75 Synthetics 60° 54 0.9 Delicates 40° 63 0.55 Wool / Handwash 40° 62 0.4 The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on the quantity and type of laundry, on the inlet water temperature and on the ambient temperature. (*) «Economy 60°C» with a load of 7 kg is the reference programme for the data entered in the energy label, in compliance with EEC 92/75 standards. For the duration of please the display on thecontrol panel. 40 Installation Installation Unpacking All transit bolts and packing must be removed before using the appliance. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. 1. After removing all the packaging, carefully lay machine on it’s back to remove the polystyrene base from the bottom. 2. Remove the power supply cable and the draining hose from the hose holders on the rear of the appliance. 3. With the supplied spanner unscrew and remove the central rear bolt A. Installation 41 4. Unscrew and remove the two large rear bolts B and the six smaller bolts C. 5. Remove the bracket D and refit the six smaller bolts C. Slide out the relevant plastic spacer E. 6. Open the porthole, take out the inlet hose from the drum and remove the polystyrene block fitted on the door seal. 7. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet. 8. Connect the water inlet hose as described under the paragraph «Water inlet». All the different plug caps are supplied with the appliance in the plastic bag containing the instruction booklet. 42 Installation Positioning and levelling Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Before placing it on small tiles, apply a rubber coating. Never try to correct any unevenness in the floor by putting pieces of wood, cardboard or similar materials under the machine. If it is impossible to avoid positioning the machine next to a gas cooker or coal- burning stove, an insulating panel covered with aluminium foil on the side facing the cooker or stove, must be inserted between the two appliances. The machine must not be installed in rooms where the temperature can drop below 0. The water inlet hose and the drain hose must not be kinked. Pl...