Bushnell Night Vision products are comprised of high quality image intensifier tubes and optics. Bushnell Night Vision products amplify existing light, allowing you to see in dark conditions too dark for the naked eye. HOW NIGHT VISION WORKS Bushnell Night Vision products collect and amplify existing light through the objective lens, which is then focused on the image intensifier. Inside the intensifier, a photocathode is “excited” by the light and converts the photon energy into e l e c t rons.

Plug the adapter’s two prongs into the outlet, and replace the center screw. Now plug the tool or machine into the adapter. DO NOT MODIFY THE PLUG IN ANY WAY. IFYOU HAVE ANY DOUBT, CALL A QUALIFIED ELECTRICIAN. Extension Cords If your tool is double insulated and has a two-prong plug, you may use either a two or three-prong extension cord. If your tool has a grounded, three-prong plug, you must use a three-prong extension cord with three-prong receptacles. Only use rounded jacket extension cords

High speed can build friction while sanding and cause heat check in some woods. 2. Begin with fine sandpaper (120 grit) and progress through each grit, using only light pressure. Coarser sandpaper tends to leave deep scratches that are hard to eliminate. Use power-sanding techniques to avoid concentric sanding marks around your finished piece. Avoid rounding over the rim and foot with sandpaper; try to keep details crisp. Finish sanding with 220 grit. 3. Remove sanding dust with tack rags or com

TABLE OF CONTENTS Safety Rules ...............................................................................................................................................4-5 Safety: Decals ...............................................................................................................................................6 Specifications ................................................................................................................................................7 R

This tool is used for smoothing cylinders, for cutting shoulders, beads, vee-grooves, etc. The spear or diamond-point chisel and the round-nose chisel are scraping tools which are used where their shape fits the contour of the work. The parting tool is a double-ground chisel, and is used for cutting-off and for making straight incisions or sizing cuts to any required diameter. Cl Î w GOUGË ; SKEW SPEAR; GOUGE PARTING RP.NÔSE GOUGE SKEW Fig. 27 Fig. 28 13 Fig. 29 CENTERING THE WORK Woo

434-08-651-0006 ©Delta International Machinery Corp. 1997 12" Variable Speed Wood Lathe (46-700 Bench Model) (46-701 Floor Model) INSTRUCTION MANUAL TABLE OF CONTENTS SAFETY RULES...............................................................................................................................................................3 ADDITIONAL SAFETY RULES FOR WOOD LATHES...................................................................................................4 UNPACKING AN

23G Snap Ring 2 24G Bearing 2 25G Plunger 1 26G Spring 1 27G Bushing 1 28G Handle 1 29G Cap Nut M10 1 30G Front Cover 1 31G Cap Screw M6x15 3 32G Pin 6x22 2 33G Bracket 1 34G Cap Screw M6x10 3 35G Washer 1 36G Bushing 1 37G Pin 4x14 1 38G Plate 1 39G Rivet 2x5 2 40G Cap Screw M8x20 3 41G Spring Washer 3 42G Oil Cap 4 43G Note: When ordering parts from this list be sure to include the correct suffix. Note: Some parts are listed and shown for illustration purposes only, and are not available indiv

II is equipped with a brass plug on one end and a comfortable knob on the other. IMPORTANT: NEVER DRIVE THE WORKPIECE INTO THE SPUR CENTER WHEN IT IS MOUNTED IN THE HEADSTOCK. Instructions on setting the spur center into the workpiece are found in the “OPERATION” section of this manual. Fig. 29 TAILSTOCK LIVE CENTER The tailstock live center (A) Fig. 31, supplied with your lathe, is equipped with a No. 2 Morse Taper shank and is inserted into the tailstock spindle (B), as shown. To remove the

However, the parting tool is a rough cutter, so that ultimately the skew must be used in cleaning the cut. The whole operation can be done with the skew, and this technique is illustrated by the drawings in Figs. 49, 50 and 51. The first movement is a nicking cut with the toe of the skew, as shown in Fig, 49. This cut cannot be made very deep without danger of burning the chisel, so a clearance cut is made by inclining the skew away from the first cut and again pushing the tool into the work. Th