Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Woodstock
Dateigröße: 2.36 mb
Dateiname: w1752_m.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
• Lighting: Lighting should be bright enough to eliminate shadow and prevent eye strain. • Electrical: Electrical circuits must be dedicated or large enough to handle amperage requirements. Outlets must be located near each machine, so power or extension cords are clear of high-traffic areas. Follow local electrical codes for proper installation of new lighting, outlets, or circuits. MAKE your shop “child safe.” Ensure that your workplace is inaccessible to youngsters by closing and locking all entrances when you are away. NEVER allow untrained visitors in your shop when assem- bling, adjusting or operat- ing equipment. The Model W1752 is a heavy machine. DO NOT over-exert yourself while unpacking or moving your machine—get assistance. Cleaning Machine The bed and other unpainted parts of your lathe are coated with a waxy grease that protects them from corrosion during shipment. Clean this grease off with a solvent cleaner or citrus-based degreaser. DO NOT use chlorine-based solvents such as brake parts cleaner or acetone—if you happen to splash some onto a painted surface, you will ruin the finish. NEVER use gasoline or other petroleum-based solvents to clean with. Most have low flash points, which make them extremely flammable. A risk of explosion and burning exists if these products are used. Serious personal injury may occur if this warning is ignored! ALWAYS work in well- ventilated areas far from possible ignition sources when using solvents to clean machinery. Many solvents are toxic when inhaled or ingested. Use care when disposing of waste rags and towels to be sure they DO NOT create fire or environmental hazards. -12 W1752 Owner's Manual (Mfg. 1/07+) Assembly To install the tool rest, do these steps: 1. Turn the release lever on the tool rest base so it does not interfere with assembly. 2. Thread the tool rest lock handles into the tool rest base (Figure 4) until the threaded ends of the handles are flush with the inside of the shaft. 3. Insert the tool rest into the shaft and turn the handles to lock it as shown in Figure 5. 4. Install the optional bed extension, Model W1753 (Page 25). Refer to the instruction sheet included with the bed extension. Figure 4. Tool rest lock handles installed. Tool Rest Base Lock Handles Release Lever Figure 5. Tool rest installed. -13 SET UP W1752 Owner's Manual (Mfg. 1/07+) Test Run SET UP Complete this process once you have familiarized yourself with all instructions in this manual. The test run consists of verifying the following: 1) The motor powers up and runs correctly, and 2) the safety paddle switch works correctly. To test run the mini wood lathe, do these steps: 1. Read the entire instruction manual first! 2. Make sure all tools and foreign objects have been removed from the machine. 3. Review Page 10 and connect your machine to the power source. 4. Flip the paddle switch up to turn the machine ON. Make sure that your hand stays poised over the switch in case you need to quickly turn the machine OFF. — If you suspect any problems, immediately turn the lathe OFF and disconnect the machine from the power, and refer to Page 27 to troubleshoot/fix any problems before starting the lathe again. — If the source of an unusual noise or vibration is not readily apparent, contact our technical support for help at (360) 734-3482 or contact us online at tech-support@shopfox.biz. 5. Turn the machine OFF. 6. Remove the safety key and attempt to turn the machine ON. — If the machine starts, stop it. The switch disabling feature is not working. This safety feature must work properly before proceeding. Contact our technical support for help. — If the machine does not start, the switch disabling feature is working. Projectiles thrown from the machine could cause serious eye injury. Wear safety glasses during assembly and operation. Loose hair and clothing could get caught in machinery and cause serious personal injury. Keep loose clothing rolled up and long hair tied up and away from machinery. -14 W1752 Owner's Manual (Mfg. 1/07+) OPERATIONS General The Model W1752 will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written with the understanding that the operator has the necessary knowledge and skills to operate this machine. If at any time you are experiencing difficulties performing any operation, stop using the machine! If you are an inexperienced operator, we strongly recommend that you read books, trade articles, or seek training from an experienced lathe operator before performing any unfamiliar operations. Above all, your safety should come first! Always wear safety glasses when oper- ating the lathe. Failure to comply may result in serious personal injury. READ and understand this entire instruc- tion manual before using this machine. Serious personal injury may occur if safety and operational information is not understoo...