4. Entfernen Sie die Schneefrase vom Karton, und uberprufen Sie jenen auf weitere lose Teile. Enlever la souffleuse de la caisse en carton 1. Enlevez toutes les parties detachees et les parties de boites de carton. 2. Taillez les quatre coins de la caisse de carton et etendez les panneaux a plat. 3. Enlevez tout le materiel d’emballage sauf les liens en plastique retenant la tige de la commande de vitesse au levier de commande du bas. 4. Enlevez la souffleuse du carton et verifi ez soigneusement

(Figure 21). 1 Figure 21 1. Control bar 2. Adjuster link 3. Cable positions Inspecting the Auger Blades Before each session, inspect the auger blades for wear. When a auger blade edge has worn down have an Authorized Service Dealer replace the auger blades and the scraper (Figure 22). Figure 22 1. Auger blades 2. Scraper 12 Changing the Engine Oil Run the engine a few minutes before changing the oil to warm it. Warm oil flows better and carries more contaminants. A The engine oil wi

Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quan ti ties that can be used within 30 days to assure fuel freshness. FIG. 21 PRIM ER SAFETY IG NI TION KEY ON / OFF SWITCH CHOKE CONTROL STARTER BUTTON FUEL SHUT-OFF VALVE NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT. POWER CORD PLUG GAS O LINE FILLER CAP ENGINE OIL FILL CAP / DIPSTICK RECOIL (AUXILIAR

TRACTION DRIVE CONTROL ROD VINYL SLEEVE FIG. 3 PLASTIC TIE NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles. INSTALL SPEED CONTROL ROD (See Figs. 1 and 2) 1. R

6. REMOVE HAIRPIN FROM CLUTCH ROD and remove clutch rod from swing plate. Tip swing plate forward. 7. REMOVE AUGER BELT from around pulley. FIG. 20 BELT KEEPER IDLER ARM SQUARE HOLE BOLTS TRACTION DRIVE BELT CLUTCHING IDLER ARM BRACKET AUGER BELT FLAT WASHER AUGER PULLEY AUGER FRAME HOUSING ENGINE PULLEY BOLT FRAME ASSEMBLY AUGER HOUS ING HANDLES 17 SERVICE AND ADJUSTMENTS NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer.

IMPORTANT: Know how to operate all controls before adding fuel or attempting to start the engine. Filling the Fuel Tank Fill the fuel tank with fresh unleaded gasoline, do not exceed 87 octane rating (Figure 8). IMPORTANT: Do not add oil to the gasoline. IMPORTANT: Do not use E85 blended fuels. This engine is not E20/E30/E85 compatible. Alternative fuels with high alcohol content can cause hard starting, poor engine performance, and may cause internal engine damage. Checking the Engine Oil Level

El portaherramientas esta situado sobre la cubierta de la correa. Guarde los pernos de cizalla de recambio, tuercas y llave multiple de tuercas en la bolsa de partes del portaherramientas. NOTA: La llave de apriete multiple se puede usar para montar la cabeza rotante del conducto a la maquina quitanieves y para hacer regulaciones de las placas de deslizamiento. Hoe uw sneeuwruimer te monteren Gereedschapskist Uw sneeuwruimer is voorzien van een gereedschapskist. De gereedschapskist is bevestigd

Water in engine can result in shortened engine life.. 14 15 SERVICE AND ADJUSTMENTS WARNING: To avoid serious injury, before performing any service or adjust ments: 1. Be sure the on/off switch is in the OFF position. 2. Remove safety ignition key. 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it can not come in contact with plug. SNOW THROWER TO ADJUST SNOW THROWER HEIGHT See “TO ADJUST SKID PLATES” and

Damage to the snow thrower can result. • Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the operation of the snow thrower. NOTE: When both traction drive and auger control levers are engaged, the traction drive control lever will lock the auger control lever in the engaged position. This will allow you to release your right hand from the handle and adjust the disc

7. Clean around the oil filler cap/dipstick (Figure 24). 8. Unscrew the oil fill cap/dipstick and remove it (Figure 24). 9. With the snowthrower in the operating position, carefully pour oil into the oil fill hole until "Full" on the fill cap/dipstick line (Figure 26). Max fill: 18 oz. (0.5 l), type: automotive detergent oil with an API service classification of SJ, SL, or higher. Use Figure 25 below to select the best oil viscosity for the outdoor temperature range expected: Figure 24 1. Oil fi