■;-?*' ^•■:-; : • •• 26" ROTARY SNOW PLOW ATTACHMENT PACKING LIST The rotary snow plow is shipped complete in a carton. INSTRUCTIONS FOR ASSEMBLING 1. Attach rotary snow plow to tractor as shown in Fig. 1. Refer to Quick-Hitch instructions in tractor manual. NOTE: Before attaching snow plow install woodruff key in slot in snow plow drive shaft and place the drive sheave on the drive shaft with hub of sheave to outside as shown in Fig. 2. The snow plow drive sheave is part No. GSA21 with a %

Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA MANUFACTURING, INC. © Copyright Simplicity 2003 Manufacturing, Inc. All Rights Reserved. Printed In USA. TP 400-3876-00-AT-SMAN Mfg. No. Description Attachment 1694403 46" Single-Stage Snowthrower Body & Rotor Group NOTE: Unless noted otherwise, 986350 use the standard hardware torque specification chart. Torque to Clearance between outside of sprocket and side plate to be .81 +/- .060. 1536 35 16 11 29 22 24 20 19 21 25 23 26 27 1 4

Pulley will not be re-used in this installation. 6. See figure 3. Replace the two 3/4 taptite screws as shown with two 5/16-18 x 1-1/2 taptite screws supplied. 7. See figure 4. Position the pulley bracket assy. (A) on the 1-1/2 taptite screws installed in step 6. Install the double groove pulley (B) to the arbor shaft. Reinstall the capscrew, lockwasher, and large flat washer removed in step 5. Torque capscrew to 50-70 ft.-lbs. (68-76 Nm). 8. Mfg. No. 1691867 only. See figure 4. Install new b

No. Description 1691520 42” Snow Plow/Dozer Blade Hitch Mfg. No. Description 1692039 Hitch (for Landlord / 1700 / 2700 Series & Broadmoor / 1600 / 2600 Series) 1692624 Hitch (for Regent / 500 / 2500 Series) 1715046-02 Rev 10/97 TP 100-2122-02-AT-SMA Table of Contents Recommended Accessories...................................................................................................................................1 Safety Rules................................................................

Tighten the setscrew. Raise the snowthrower and recheck the measurement. Readjust if necessary. 3. The scraper blade will float over the surface bumps or dig into them depending on the down pressure. The initial adjustment made during snowthrower installation may be suitable. If not, fully raise the snowthrower. Loosen the setscrew in the rear set collar (D). To allow scraper blade to float more, move the rear set collar toward the rear. To increase down pressure, move the rear set collar towar

Store the spring clip in the lift rod hole. 4. Push the belt tensioning lever down. 6 Installation & Removal 5. Remove the belt from the PTO pulley (A, figure 5) and from the two idler pulleys (B & C). If a mower attachment is to be used on the tractor, remove the front idler pulley (D, figure 4) and install it in upper tab. 6. Remove the snowthrower from the tractor by using either one of the following methods “a” or “b”. (The belt may remain on snowthrower pulley unless removal is desired

Be thoroughly familiar with the controls and proper use of the equipment. Know how to stop the unit and disengage the controls quickly. •Never allow children to operate the machine. Do not allow adults to operate it without proper instruction. •Keep the area of operation clear of all persons, particularly small children and pets. • Do not carry passengers. • Make sure: a. tractor and attachments are in good operating condition. b. all safety devices and shields are in place c. and in good

Never attempt to clean snow from excessively steep slopes. The maximum slope for any opera tion is 17.7% (10’). CHECKS BEFORE EACH START-UP 1. Make sure all safety guards are in place. and all nuts, bolts and clips are secure. 2. Check the engine oil level. See your engine Owner’s Manual for procedure and specifications. 3. Check the fuel supply. Fill the tank to within l/4 to i/2 inch of top of tank to provide space for expansion. See your engine Owner’s Manual for fuel recommendations. with ca

No. 1691411 Mfg. No. 1691413 Mfg. No. 1691414 BakerTM OPERATOR’S MANUAL Model 7/22E 500 N. Spring Street, P.O. Box 997 Port Washinnton, WI 53074-0997 Table Of Contents SAFETY RULES General ........................................................... 2 Preparation.. .................................................. .2 Operation.. ..................................................... .2 Maintenance & Storage.. .............................. .3 Safety Decals ........................................

Tighten screws in control bracket. 5. Check adjustment by moving lever to each position. Be sure to check to see that NEUTRAL is properly reached from both forward and reverse directions. 6. Check shift lever movement from reverse to 3rd and make sure lever does not contact handles. To adjust, loosen two screws indicated in figure 9, move lever slightly, then tighten the screws and check again. DRIVE BELTS The snowthrower is equipped with two drive belts located just in front of the engine under