Anleitung Honda Automobiles, modell SB7038
Hersteller: Honda Automobiles Dateigröße: 1004.63 kb Dateiname: 01bf160f-914b-3e04-911b-6a63ac451226.pdf
Unterrichtssprache:
|
|
|
|
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite
Anleitung Zusammenfassung
If the snow is deep, reduce the ground speed. Always operate the snowblower with the throttle set to FAST. Using other throttle settings can reduce performance and clog the discharge chute. Traction The standard turf tires on the mid-size commercial mower power head extend beyond the width of the snowblower. This can reduce the performance of the snowblower. Narrower, AG (bar-tread) tires are recommended for best performance. Never use tire chains. Removing and Storing the Snowblower_SB7038 Snowblower Removing and Storing the Snowblower Refer to the illustrations in the Installation section as needed. Deflector Cable Removal 1. Loosen the deflector cable nut at the operator’s end, and remove the cable from the chute control cable bracket. 2. Remove the cotter pin and clevis pin from the clevis. Remove the screws, spacer, washers and nuts from the hold-down clamp. Remove the deflector cable from the snowblower. Chute Rotator Removal 1. Remove the spring clip and pull the upper crank handle free of the lower crank and crank support. 2. Remove the hook end of the lower crank from the worm gear by pressing in the spring-loaded section. 3. Remove the two 3/8” bolts and flange nuts to remove the crank support. Snowblower Removal 1. Loosen the top nuts on the engine belt guides, and remove the snow blower belt from the engine pulley. 2. Support the snowblower with a suitable block of wood or other support. 3. Unbolt the snow blower from the power unit and remove the snow blower. 4. Open the pump bypass valves (on hydrostatic drive units) and pull the power head away from the snowblower. Close the pump bypass valves. Storing the Snow Blower 1. Clean the snow blower thoroughly, and paint any areas where bare metal is showing. 2. Replace any worn or damaged parts. 3. Lubricate the snow blower as described in Lubrication. 4. Store in a dry area. Do not cover with a plastic tarp or other material which will trap moisture. Maintenance & Adjustments Maintenance Schedule What When Notes Lubricate chains Every 2 hours use chainsaw oil Apply grease to antifriction ring Every 25 hours use general purpose grease Apply grease to bushings Every 25 hours use general purpose grease Apply grease to worm gear Every 25 hours use general purpose grease Inspect and adjust PTO spring tension Every 25 hours adjust tension if needed Grease fitting on auger Every 25 hours use general purpose grease Gearbox oil Every 25 hours use AGMA 5 EP or SAE 90 hypoid gear oil A WARNING You can be seriously injured by the fan or auger blades. The blades spin and can cut or amputate your hand or fingers. Always stop the engine, remove the ignition key, and disconnect the spark plug cap(s) before attempting any maintenance or adjustments. Adjustments Skid Shoes The skid shoes should be adjusted based on the type of ground surface. See page 20 for details on adjusting the skid shoes. Lubrication Chain The chain must be lubricated on a regular basis for proper operation. 1. Always park the snowblower on a flat, level surface, and remove the ignition key before attempting to lubricate the chain, 2. Remove the two belt cover knobs and the belt cover. 3. Apply chain saw oil to the gearbox sprocket, snowblower sprocket and chain. Avoid getting any oil on the belt or pulley. Discharge Chute & Worm Gear Apply a liberal amount of general purpose grease to the outer edge of the antifriction ring on the base of the discharge chute. Apply grease to the worm gear and the sector on the discharge chute. Bushings Apply a liberal amount of general purpose grease to the insides of the worm gear bushings and the crank handle bushing. Wipe away any excess grease from the outside of each bushing. SB7038 Snowblower Discharge Chute 1 hand guard 1 2 1/4 x 3/4* hex bolt 2 3 1/4' Hat washer 2 4 1/4" lock washer 2 5 1/4" hex nut 2 6 anti-friction ring 1 7 1-5/18" bushing 1 s 1-11/16" bushing 1 9 bushing support 1 10 rotation worm 1 11 hold down plate 4 12 1/4 x 1/2" hex bolt 6 13 1/4/x 3/4" hex bolt 2 14 self-locking nut 2 15 5/16" nylon washer 2 16 3/8" nylon washer 2 17 hex bolt 2 18 spring 2 Optional Accessories A number of accessories are available for your snowblower to enhance operation and use. Headlight Kit This is a single-lamp light kit that mounts to the crank support rod. The light features an integrated, weather-resistant on/off switch and 50 watt halogen bulb. Engine Cold Weather Kit The cold weather kit is a cover for the cooling air intake. It helps the engine maintain proper operating temperature when used in cold weather conditions. AG Tire Kit For best traction, use of AG {bar tread) tires are recommended. The AG tire kit includes two bar tread tires and wheels. The standard turf tires extend beyond the width of the snowblower and can reduce performance. Carburetor Anti-Icing Kit (HRC7013 models only) This special kit is used to prevent the formation of ice on the carburetor linkage....