Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Barrel length: 58 cm / 23“ Total length: 105 cm / 41“ Weight approx.: 2.5 kg / 5.5 lbs Magazine: 5-shot 1417 Caliber: .22 l.r. Barrel length: 35 cm / 14“ Total length: 83 cm / 32.5“ Weight approx.: 2.4 kg / 5.2 lbs Magazine: 5-shot 1502 Caliber: .17 HM 2 Barrel length: 58 cm / 23“ Total length: 105 cm / 41“ Weight approx.: 2.7 kg / 6.0 lbs Magazine: 5-shot 1516 Caliber: .22 Win. Mag. R.F. Barrel length: 58 cm / 23“ Total length: 105 cm / 41“ Weight approx.: 2.5 kg / 5.5 lbs Magazine: 4-shot 1517 Caliber: .17 HMR Barrel length: 58 cm / 23“ Total length: 105 cm / 41“ Weight approx.: 2.5 kg / 5.5 lbs Magazine: 4-shot Heavy Barrel rifles are approx. 0.2 kg / 0.5 lbs heavier. a fig.2 aa fig.2 a fig.1 Before first shooting •Wipe away excess oil from the surface of the barreled action and the rifle. •Pull a cleaning patch through the barrel from the chamber towards the muzzle several times. Cocking, loading and safety operation •Degrease the bolt and the interior of the barrel without leaving lint. •Open the reinserted bolt and pull it back to the stop. •Now push the bolt forward to close the breech. A cartridge from the magazine is fed into the chamber of the barrel. Now push the bolt handle completely downwards. The bolt is now cocked, the rifle is ready for shooting. •After firing, lift the bolt handle and pull the bolt fully to the rear. This will cock the bolt again and eject the empty case. The lateral safety can be operated in cocked condition. The rifle is •safe when the red dot on the receiver is covered (fig. 1). •ready for shooting when the red dot on the receiver is visible (fig. 2). Please note: The safety lever must latch properly in one of the two positions. The lever must never be situated between the two. When the safety wing is actuated, the trigger must not be touched. The trigger must not be released either when the safety wing is in the „safe“ position. Safety: The safety at the receiver locks the trigger. With regard to safety aspects the safety advertently is hard to move. Nevertheless, the bolt can be opened also in the “safe“ position, for example to remove a cartridge from the case. You can only operate the safety lever when the bolt is cocked. Unloading For safety reasons the rifle must immediately be unloaded if you intend to stop shooting. Remove the magazine and open the bolt. This will eject the cartridge. Please also see safety instructions for the handling of rifles and firearms. Magazine •Remove the magazine from the magazine well. •Push the cartridges with the head first into the magazine. •Push the magazine into the magazine well until you hear that the magazine holder has caught the magazine. •Now open the bolt completely, push it forward and lock it. Thus the first cartridge of the magazine is fed into the barrel, the firing pin is cocked. The rifle is now ready for shooting. Bolt The ANSCHUTZ bolt The ANSCHUTZ bolt is designed to be extra strong and reliable and is manufactured to the closest tolerances. Bolt and came are lapped to assure very smooth operation. To disassemble the bolt •Disengage the trigger by pulling the safety forward. •Pull the trigger guard and simultaneously press the left lever (for right hand versions) forward. •Let the trigger guard go and remove the bolt over the released lock. To re-assemble the bolt Follow the disassembly procedure in reverse order. Make sure when inserting the bolt that the pin on the bolt head is in line with the groove of the chamber. Trigger The trigger has been pre-set by the factory in an optimum way and guarantees utmost safety. Warning: Your ANSCHUTZ trigger offers you a variety of individual adjustment possibilities. Please note that your rifle always must be unloaded when any adjustment is carried out. Please see the adjusting range for the referring model from the trigger chart. It might be necessary to remove the stock from the barreled action for adjustments at the trigger. Trigger adjustments must only be carried out by an authorized gunsmith. Modifications at factory-set triggers might cause severe injuries or death. Please also see the chapter „General Handling of Rifles and firearms“. Two and single stage triggers 5094 3 2 1 1. Trigger weight Adjust the trigger weight with set screw No. 2: •if you turn it to the right (clockwise): trigger weight is increased (+) •if you turn it to the left (counter-clockwise): trigger weight is decreased (-) Trigger weight and first stage weight depend on each other with regard to the mechanic mechanism. If one of them is changed there will always be a corresponding change of the other as well. 2. Sear engagement The sear engagement is the distance between the second stage and the release of the trigger. Important note: To protect your precise trigger and to guarantee perfect operation you should always close the action carefully. If the sear engagement of single stage triggers is too small and the trigger weight is too low or if the first stage of two-stage triggers is too short, ...