press the [Cancel] key. 269 What to do if Something Goes Wrong Machine Status Cause Action Nothing happens when you press the [Connect] key. The master unit or sub-unit needs a fresh supply of toner or staples. Solve the problem in the appropriate unit. Reference See . P.277 “B Loading Paper” See . P.283 “D Changing the Toner Bottle” See . P.299 “d Adding Staples” See . P.305 “y Removing Punch Waste” For any other problems, follow the instructions that are displayed. To exit Connect Copy mode, p

v Slip Sheet Copy Use this function to insert the slipsheet into certain pages of your original. Preparation Before use this function, specified the paper tray for slipsheet. You can set three trays for slipsheet. See “Tray Paper Settings” in the System Settings manual. Limitation r You cannot combine with Slip Sheet function. r You cannot copy with different size or direction originals. Note r You can specify the pages up to 20. . You can use index tab stock for slipsheet. See “Tray Paper Setti

Copying from the Bypass Tray C CCCCSelect the paper size. Limitation Note . The copy paper sizes that can be selected are as follows: • A3L,B4L,A4KL,A5KL, A6L,B5KL,B6L,PostcardL, 11.17L,81/2.14L, 81/2.11KL,51/2.81/2L, 71/4.101/2KL,8.13L, 81/2.13L,81/4.13K, 11.14L,11.15L,10.14L, 10.15L,81/4.14L, 8.101/2KL,8.10KL, 8KL,16KL,37/8" .71/2"L, 41/8" . 91/2"L,C5 EnvL,C6 EnvL,DL EnvL D DDDDPress the [OK] key. E EEEEPlace your originals, and then press the { {{{{Start} }}}}key. When copying onto custom siz

If you do, your settings will be cleared and D will appear again because the machine will not recognize that toner has been added. . Always add toner after the machine instructs you to add toner. . Do not use used toner. This will damage the machine. Note . You can still make about 50 copies after D appears, but replace the toner early to prevent poor copy quality. Reference Regarding toner storage, . p.27 “Toner Storage”. • 1: Open the front cover of the machine. • 2: Lift the green lever. • 3:

F FFFFPress the [OK] key. 115 Copying G GGGGPlace your original, and then press the { {{{{Start} }}}}key. Double Copies One original image is copied twice on one copy as shown in the illustration. Limitation . The originals of size A5L (51/2" . 81/2"L) cannot be detected properly on theexposureglass.Besureto select the copy paper manually or set the originals in the document feeder. . You cannot use the bypass tray with this function. Note . You can insert separation lines between repeated image

. p.43 “Rotated copy” . ....Manual Paper Select Choose the tray containing the paper you wish to copy onto: a paper tray, bypass tray or large capacity tray (LCT). Reference . p.61 “Copying from the Bypass Tray” Limitation . Only the paper trays set to "No Display" or "Recycled Paper" in "Paper Type", and also set to "Yes" in "Apply Auto Paper Select", can be selected in Auto Paper Select mode. . "Paper Size Setting" in the System Settings manual . If you set all the paper trays other than "No D

Make sure the paper is placed correctly so that it is fed straight. *5 It is recommended to place one sheet at a time. *6 The paper tray fence is fixed. If you wish to change the size of paper placed in this tray, contact your service representative. *7 When loading paper, make sure that the stack height does not exceed the lower limit mark of the paper tray 2. . p.160 “Setting special paper in the Paper Tray 2” *8 When the paper size is larger than A4L, you can load 10 sheets. When the paper si

57 AdonisC3_GBcopyF_FM1.book Page 58 Thursday, November 28, 2002 1:53 PM Copying Centre/Border erase Selecting [Diff. Width] A Press [Diff. Width]. A AAAAPress [Edit/Stamp]. 2 B BBBBPress [Erase]. C CCCCPress [Centre/Border]. D DDDDSet the border to be erased. Selecting [Same Width] A Press [Same Width]. B Press [Centre], and then set the erase centre width with [n nnnn] and [o oooo]. C Press [Border], and then set the erase border width with [n nnnn] and [o oooo]. D Press [OK]. B Press the key

To get maximum versatility from this machine all operators are requested to read this manual carefully and follow the instructions. Please keep this manual in a handy place near the machine. For safe and correct use of this machine, please be sure to read the Safety Information in the General Settings Guide before you use it. Notes: Some illustrations in this manual might be slightly different from the machine. Certain options might not be available in some countries. For details, please contact

One of the following eight messages can be stamped on copies with a frame around it: "COPY", "URGENT", "PRIORITY", "For Your Info.", "Preliminary", "For internal use", "CONFIDENTIAL", "DRAFT". 2 B BBBBPress the [Stamp] key. C CCCCPress the [Background Numbering] key. D DDDDEnter the number to start counting from with the number keys. Note . To change the entered number, press the [Clear] or { {{{{Clear/Stop} }}}} key and enter the new number. E EEEEPress the [OK] key. F FFFFPress the [OK] key. 6