Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Canon Dateigröße: 4.98 mb Dateiname: Unterrichtssprache:

Set 5-16 Routine Cleaning Cleaning the ADF Roller Cleaning the ADF Roller The imageRUNNER 1670F/1630 models have an ADF. If the ADF roller is dirty, your documents will be dirty after you feed them into the ADF. You can clean the ADF roller using the setting from the menu. NOTE If a paper jam occurs in the ADF, remove jammed paper from the ADF (see “Removing Jammed Paper from the ADF,” on p. 6-6), then perform the procedure below. Set .. 1 Press [Additional Functions]. 2 Press [4 ] or [e] to select . press [Set]. 3 Press [4 ] or [e] to select . ADJUST/CLEAN 2.CLEAN ADF ROLLER 5 Routine Set 4 Open the ADF. If you attempt to clean the ADF roller when the ADF is closed, the message appears. 5 Press [Set]. START CLEAN : [SET] END CLEAN : [STOP] Routine Cleaning 5-17 Set Set 6 Each time you press [Set], the ADF roller rotates about 1/3 of the roller. Wipe the ADF roller with a dry cloth. ADF Roller 5 Routine Maintenance Repeat this step until the ADF roller is clean. CAUTION Do not touch the ADF roller while it is being rotated. Your fingers or clothing may be pinched in the roller, resulting in personal injury. 7 Press [Stop/Reset] to finish the cleaning. The LCD returns the machine to the Standby mode. .. 5-18 Routine Cleaning Replacing the Toner Cartridge Replacing the Toner Cartridge This section describes how to remove the used toner cartridge and replace it with a new one. When the message or appears in the LCD, replace the toner cartridge. WARNING Do not throw the toner cartridge into open flames, as this may cause the toner inside the toner cartridge to ignite and result in burns or a fire. CAUTION When you remove the toner cartridge from the machine or the sealing tape from the toner cartridge, handle it carefully. Otherwise, the toner may scatter and get into your eyes or mouth. In this case, rinse out your eyes or mouth thoroughly with water immediately and consult a doctor. IMPORTANT There are some areas inside the machine that are subject to high-voltages and high- temperatures. Take adequate precautions when performing internal inspections to avoid burns or electrical shock. NOTE When removing the toner cartridge, take care not to allow the toner to come into contact with your hands or clothing. If they become dirty, wash them immediately with cold water. Washing with warm water will set the toner and make it impossible to remove the toner stains. 5 Routine 1 Open the toner supply cover. Replacing the Toner Cartridge 5-19 2 Pull the toner cartridge lever towards you. 3 Holding the lever, turn it clockwise so that the mark on the toner cartridge aligns with the . mark on the machine . Holding the toner cartridge lever, keep the toner cartridge level and pull it out slowly from the machine .2 5 2 .. Routine Maintenance IMPORTANT Please throw away the used toner cartridge without rocking it. 4 Unpack and rock the new toner cartridge five or six times to distribute the toner evenly. 5 Holding the toner cartridge lever, insert the toner cartridge slowly into the machine as far as it will go. 5-20 Replacing the Toner Cartridge 6 Holding the toner cartridge steady with one hand, firmly and slowly pull the sealing tape tab with the other hand to remove the sealing tape completely. Throw the tape away. IMPORTANT To avoid breaking the tape, do not pull it at an angle. 7 Holding the toner cartridge lever, turn it counterclockwise so that the . mark on the toner cartridge aligns with the . mark on the machine 1.Close the toner cartridge lever 2. 5 1 2 Routine 8 Close the toner supply cover. Replacing the Toner Cartridge 5-21 Repacking and Transporting the Machine Repacking and Transporting the Machine Be sure to disconnect the power cord before transporting the machine. If the machine is likely to be subjected to vibration (for example, when transporting over long distances), be sure to take the precautions described below. If you do not follow these precautions, the machine may be damaged or the quality of your copy images may be adversely affected. 5 Routine Maintenance 1 Disconnect the power cord. 2 If the machine is connected to a telephone or PC, remove the telephone line or cable. 3 Lift the platen unit lever, slide the platen unit and open the drum cartridge cover. 4 Pull out the shipping attachment inserted in the holder when installing the machine. (The removed shipping attachment is needed in step 6.) 5 Close the drum cartridge cover and slide the platen unit to the original position. 5-22 Repacking and Transporting the Machine 6 Attach the shipping attachment on the left side of the machine using a coin. Shipping Attachment NOTE Affix the label that was removed from the machine during unpacking. Lifting the Machine Be sure to lift the machine using the handles on each side. 1 Remove the output tray and close the stack bypass. 2 Grip the handles on the sides of the machine and lift u...

Herunterladen

Geben Sie zwei Ziffern: