Stimmen - 5, Durchschnittliche Bewertung: 4.4
(
)
)
|
Anleitung Zusammenfassung
There is a safety device which allows the laser to be switched on only if the motor is rotating above the threshold for its correct scanning speed. The motor and the laser beam can be switched off through a software command (see also the WinHost Help On Line). 1 8 3457 6 2 AVOID EXPOSURE LASER LIGHT EMITTED FROM THIS APERTURE LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT MAX. OUTPUT RADIATION 1mW EMITTED WAVE LENGTH 630-680 nm TO EN 60825-1:2001 CAUTION-CLASS 3B LASER LIGHT WHEN OPEN AVOID EXPOSURE TO BEAM This product conforms to the applicable requirements of 21CFR1040 at the date of manufacture. Figure A 1 2 3 4 Laser On LED Laser Beam Output Window Laser Warning and 8 7 6 5 Good Read LED Device Class Label TX Data LED Power On LED Mounting Holes Ext Trig LED For further details on product installation, see the complete Installation Manual. DS1100 can be configured through the WinHost Windows-based software program available on the installation CD-ROM. For configuration it is necessary to create a cable connecting the scanner to the PC as indicated in the “How To Build A Simple Interface Test Cable” section of this guide. Power Supply: - This product is intended to be installed by Qualified Personnel only. - This accessory device is intended to be supplied by a UL Listed or CSA Certified Power Unit with «Class 2» or LPS power source which supplies power directly to the scanner via the 25-pin connector. Warning and Device Class Label The laser diode used in this device is classified as a class 3B laser product according to EN 60825-1 regulations and as a Class IIIb laser product according to CDRH regulations. As it is not possible to apply a classification label on the laser diode used in this device, the following label is reproduced below. LASER LIGHT AVOID EXPOSURE TO BEAM CLASS 3B LASER PRODUCT MAX. OUTPUT RADIATION 7 mW EMITTED WAVE LENGTH 630~680 nm TO EN 60825-1 (2001) Laser Diode Class Label Any violation of the optic parts in particular can cause radiation up to the maximum level of the laser diode (7 mW at 630 to 680 nm). WEEE Compliance: DS1100 QUICK GUIDE DS1100 - X X X X Optical Resolution 1 = Standard resolution 2 = High resolution Communication Interface 1 = RS232 + RS485 Optic Version 0 = Linear 1 = Raster Reading Window Position 0 = Direct 1 = 90° Reading Performance: Version Reading Distance Max Code Resolution mm (mils) Speed scans/s 1XXX 30 mm (1.2 in) - 220 mm (8.7 in) on 0.50 mm (20 mils) codes 0.20 (8) 500 2XXX 10 mm (0.4 in) - 110 mm (4.3 in) on 0.30 mm (12 mils) codes 0.12 (5) 500 Technical Features: ELECTRICAL FEATURES SOFTWARE FEATURES Power Supply 5 Vdc ± 5% Readable Codes EAN/UPC (including Add-on 2and Add-on 5) Code 39 2/5 Interleaved Code 128 EAN 128 Code 93 Codabar Pharmacode Power Consumption 1.5 W maximum Main Serial Interface RS485 Half-Duplex Auxiliary Interface RS232 Baud Rates 150 to 115200 Inputs External Trigger; IN1 Outputs OUT1, OUT2 User-defined VCE max. 50 Vdc Collector Current 50 mA continuous max. Headers and Terminators Up to four header and four terminator characters VCE Saturation 0.3 V at 10 mA max. Power Dissipation max. 200 mW at 40 °C (Ambient temp.) Operating Modes On-Line, Automatic, Serial-On-Line, Test OPTICAL FEATURES Special Functions Motor On/Off sw commands Laser On/Off sw commands Light Source Semiconductor laser diode Wavelength In the range 630 to 680 nm Configuration Modes Through menus using WinHost utility Host Mode (commands from one of the serial ports) Safety Class Class 2 - EN 60825-1;CDRH ENVIRONMENTAL FEATURES Operating Temperature 0° to +45 °C (+32° to +113 °F) Decoding Safety Can enable multiple good reads of the same code Storage Temperature -20° to +70 °C (-4° to +158 °F) Code Selection Up to six different codes during one reading phase Humidity max 90% non condensing Vibration Resistance IEC 68-2-6 test FC 14 mm @ 2-10 Hz 1.5 mm @ 13-55 Hz 2 g @ 70-200 Hz 2 hours on each axis Parameter Storage Non-volatile internal EEPROM Shock Resistance IEC 68-2-27 test EA 30g; 11 ms; 3 shocks on each axis PHYSICAL FEATURES Dimensions 80x50x24 mm (3.15x1.9x1 in) Protection Class IP65 Weight without Cable <100 g. (3.53 oz) USER INTERFACE LED Indicators Power ON, Good Read, External Trigger, Data TX; Laser ON Accessories: Name Description Part Number DC5-2200 DC converter 4-30 Vdc to 5 Vdc 93ACC1040 DS1100 QUICK GUIDE 3 Electrical Connections: DS1100 is equipped with a cable terminated by a 25-pin female D-sub connector for connection with the power supply and input/output signals. CAUTION Do not connect GND and SGND to different (external) ground references. GND and SGND are internally connected through filtering circuitry which can be permanently damaged if subjected to voltage drops over 0.8 Vdc. The details of the connector pins are indicated in the following table: 25-pin D-sub female connector pinout Pin Name Function 9, 13 VS Power supply input voltage + 25* GND Power supply input voltage - 1* CHASSIS Chassis ground 2, 21 TXAUX...