Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Shindaiwa Dateigröße: 2.11 mb Dateiname: Unterrichtssprache:

During the breakin period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as required. High Altitude Adjustment High altitude adjustment is not required for proper operation of this engine. Level 2. Tools required: Parts required: Screwdriver, tachometer None. NOTE Every unit is run at the factory and the carburetor is set in compliance with emission regulations. This carburetor does not have acceleration and high speed adjustment needles. 1. Before adjusting the carburetor, clean or replace the air filter and spark arrestor screen and blower pipes are installed. 2. Start engine and run for several minutes to reach operating temperature. 3. Stop engine. Turn red HI speed needle (A) CCW (counter clockwise) to stop. 4. Idle Speed Adjustment with tachometer. •Start engine and turn “idle” speed adjustment screw (B) to idle RPM found on page 21 in the "Specifications" section of this manual. 5. Accelerate to full throttle for 2-3 seconds to clear excess fuel from engine then return to idle. Accelerate to full throttle to check for smooth transition from idle to full throttle. If engine stops or stalls after full warm up return the unit to your authorized Shindaiwa dealer for repair. 6. Check HI speed RPM at W.O.T. (Wide Open Throttle). HI speed RPM should be set to specifications found on page 21 "Specifications" of this manual. 7. Check idle speed and reset if necessary. 18 Troubleshooting TROUBLESHOOTING CHART Problem Check Status Cause Remedy Fuel at carburetor No fuel at carburetor Fuel strainer clogged Fuel line clogged Carburetor Clean or replace Clean or replace See your Shindaiwa dealer Fuel at cylinder No fuel at cylinder Carburetor See your Shindaiwa dealer Engine cranks -starts hard/ doesn't Muffler wet with fuel Fuel Mixture too rich Open choke Clean/replace air filter Adjust carburetor See your Shindaiwa dealer start Spark at end of plug wire No spark Stop switch off Electrical problem Interlock switch Turn switch to ON See your Shindaiwa dealer See your Shindaiwa dealer Spark at plug No spark Spark gap incorrect Covered with carbon Fouled with fuel Plug defective Adjust to .65mm (0.026 in.) Clean or replace Clean or replace Replace plug Air filter Air filter dirty Normal wear Clean or replace Fuel filter Fuel filter dirty Contaminants/residues in fuel Replace Engine runs, but dies or does not Fuel vent Fuel vent plugged Contaminants/residues in fuel Clean or replace Spark Plug Plug dirty/worn Normal wear Clean and adjust or replace accelerate properly Carburetor Improper adjustment Vibration Adjust Cooling System Cooling system dirty/plugged Extended operation in dirty/dusty locations Clean Spark Arrestor Screen Spark arrestor screen plugged Normal wear Replace Engine does not crank N/A N/A Internal engine problem See your Shindaiwa dealer Engine runs, blower doesn't work or is weak/uneven Blower pipe Pipe clogged Build-up of debris Unclog Pipe loose Vibration Tighten Pipe damaged Wear/Misuse Replace A DANGER Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result. J 19 English English Storage A WARNING During operation the muffler or catalytic muffler and surrounding cover becomes hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long Term Storage (Over 30 Days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 1. Store unit in a dry, dust free place, out of the reach of children. 2. Place the stop switch s in the "STOP" position. 3. Remove accumulation of grease, oil, dirt and debris from exterior of unit. 4. Perform all periodic lubrication and services that are required. 5. Tighten all screws and nuts. 6. Drain the fuel tank completely and pull the recoil starter handle several times to remove fuel from the carburetor. 7. Remove the spark plug and pour 7cc (1/4 oz.) of fresh, clean Shindaiwa 2-stroke engine oil into the cylinder through the spark plug hole. A. Place a clean cloth over the spark plug hole. B. Pull the recoil starter handle 2-3 times to distribute the oil inside the engine. C. Observe the piston location through the spark plug hole. Pull the recoil handle slowly until the piston reaches the top of its travel and leave it there. 8. Install the spark plug (do not connect ignition cable). 9. Remove blower pipe assembly from unit. 20 Specifications MODEL----------------------------------------------------EB212 Hand Held Length ...................................................... 330 mm (13.0 in.) (w/o pipes) Width........................................................215 mm (8.5 in.) Height.........

Herunterladen

Geben Sie zwei Ziffern: