Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
[F2] Porta . Mono/Poly Mode = mono [VOICE] . [EDIT] . Element selection . [F1] Oscillator . XA Control [VOICE] . [EDIT] . Element selection . [F1] Oscillator . Element Group 68 MOTIF XF Owner’s Manual Troubleshooting • When the Element to which “Key Off Sound” of the XA Control parameter is assigned does not sound, are you releasing the note after the AEG decays? The “Key Off Sound” Element will take over the AEG level of the previous Element if both the Elements belong to the same Element Group. To solve such a problem, release the note before the AEG level decays to minimum or set the “Key Off Sound” Element to a different Element Group from the previous Elements. [VOICE] . [EDIT] . Element selection . [F1] Oscillator . Element Group • When the Element to which “AF1 on,” “AF2 on,” or “all AF off” of the XA Control parameter is assigned does not sound, is the corresponding ASSIGNABLE FUNCTION button pressed? • Is “Vocoder” selected as the Insertion Effect Type of the Voice? If so, set the parameters related to the AD Part and A/D INPUT connector to the appropriate values then play the keyboard while inputting your voice into the microphone connected to the MOTIF XF. Check whether or not the Gain Knob on the rear panel is set to the minimum position. For details, see page 47. [VOICE] . [EDIT] . [COMMON EDIT] . [F6] Effect . [SF1] Connect . INSERTION CONNECT [VOICE] . [UTILITY] . [F4] Voice Audio . [SF1] Output . Output Select = InsL [VOICE] . [UTILITY] . [F2] I/O . Input . Mic/Line = mic • When playing the keyboard in the Performance/Song/Pattern mode produces no sound, has a Voice been properly assigned to each Part? [PERFORM] . [F2] Voice [SONG]/[PATTERN] . [MIXING] . [F1] Part 1-16 • When Song/Pattern playback produces no sound, are the output channel of each track in the play mode and the receive channel of each Part in the Mixing mode set appropriately? [SONG] . [F3] Track . [SF1] Out [PATTERN] . [F3] Track [SONG]/[PATTERN] . [MIXING] . [EDIT] . Part selection . [F1] Voice . [SF1] Voice . Receive Channel • When Song/Pattern playback produces no sound, are the Velocity Rate and Velocity Offset settings of the Play FX appropriate? [SONG]/[PATTERN] . [F2] Play FX . Velocity Offset • No sound is produced when the ARP Play Only parameter is set to on and one of the following situations occurs. • When the [ARPEGGIO ON/OFF] button is turned off. • When the ARP Switch parameter of the corresponding Part is set to off. • When no Arpeggio Type is assigned to the current Voice. Playback continues without stopping. • When the [ARPEGGIO ON/OFF] button is turned on, press it so that its lamp is turned off. • When in the Song mode or Pattern mode, press the [.] (Stop) button. • When the click sound continues, check the following parameter setting. Set this parameter to something other than “always” because this setting always plays back the click sound regardless of the sequencer status. [PERFORM]/[SONG]/[PATTERN] . [SEQ SETUP] . [F1] Click . Mode Distorted sound. • Are the effect settings appropriate? Use of an effect at certain settings may produce distortion. [VOICE] . [EDIT] . [COMMON EDIT] . [F6] Effect [PERFORM] . [EDIT] . [COMMON EDIT] . [F5] Effect [SONG]/[PATTERN] . [MIXING] . [F5] Effect Use of the Master Effect at certain settings may produce distortion. [VOICE] . [UTILITY] . [F3] Voice . [SF1] Master FX [PERFORM] . [EDIT] . [COMMON EDIT] . [F2] Level/MEF . [SF2] Master FX [SONG]/[PATTERN] . [MIXING] . [EDIT] . [COMMON EDIT] . [F2] Master FX . [SF2] Master FX MOTIF XF Owner’s Manual 69 Troubleshooting • Are the filter settings appropriate? Excessively high filter resonance settings can cause distortion. [VOICE] . [EDIT] . Element/Key selection . [F3] Filter [PERFORM] . [EDIT] . Part selection . [F4] EG . Filter [SONG]/[PATTERN] . [MIXING] . [EDIT] . Part selection . [F4] EG . Filter • Is any of the following volume parameters set so high that clipping is occurring? [UTILITY] . [F1] General . [SF1] Play . Volume [VOICE] . [EDIT] . [COMMON EDIT] . [F1] General . [SF2] Play Mode . Volume [PERFORM] . [EDIT] . [COMMON EDIT] . [F2] Level/MEF . [SF1] Level . Volume [SONG]/[PATTERN] . [MIXING] . [F1] Part 1-16 . Volume Sound is cut off. • Is the entire sound (via your keyboard playback and Song/Pattern/Arpeggio playback) exceeding the maximum polyphony of the MOTIF XF? For information about the maximum polyphony, refer to the Reference Manual. Only one note sounds at a time. • When this situation occurs, the Mono/Poly parameter in the current mode is set to “mono.” If you wish to play chords, set this parameter to “poly.” [VOICE] . [F2] Porta . Mono/Poly Mode [PERFORM] . [EDIT] . Part selection . [F1] Voice . [SF1] Voice . Mono/Poly [SONG]/[PATTERN] . [MIXING] . [EDIT] . Part selection . [F1] Voice . [SF1] Voice . Mono/Poly Pitch or intervals are wrong. • Is the Master Tune parameter in the Utility mode set to a value other than “0”? [UTILITY] . [F1] General . [SF1] Play . Tune • Is the Note Shift parameter in the...
Dieses Handbuch ist für folgende Modelle:Tasteninstrumente - MOTIF XF7 (10.68 mb)
Tasteninstrumente - MOTIF XF8 (10.68 mb)