Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Kenmore Dateigröße: 8.01 mb Dateiname: Unterrichtssprache:

Draw the bobbin thread up through the fabric by holding the top thread and taking one stitch at the spot where you wish to start darning. Lowering the presser bar, start sewing at a slow to medium speed. Move the fabric back and forth with _a steady rhythm to cover the darning area. When it is covered, turn the fabric and sew another layer of stitching across the first layer of stitching. BUTTON SEWING SETTINGS Special Stitch Dial -ww_=-._ Feed Dogs -Down Zigzag Presser Foot Zigzag Needle Plate 1. Align two holes of button with slot of presser foot and lower foot to hold the button securely. 2, Turn hand wheel manually until needle point is just above button, 3. Adjust stitch width control so needle will enter left hole of the button. 4, Turn hand wheel again by hand so needle enters second hole. Readjust stitch width if necessary, Stitch a number of times. 5. Finish sewing with an extra two inches of thread remaining; Draw these threads to reverse side of garment and tie. BAR TACKING SETTINGS Special Stitch Dial -v,w_]:-=. Stitch Width Control -2 to 4 Stitch Length Control -Red Zone Special Stitch Modifier -Red Dot Zigzag Presser Foot Zigzag Needle Plate This stitch is similar to a very short satin stitch and is used to reinforce points of strain such as corners of pockets and straps on lingerie. Sew 4 to 6 zigzag stitches. FREE-ARM SEWING (Free-arm type only) This sewing machine can be used like a flat bed machine, but easily converts to free arm machine by removing the base. The free arm enables you to sew tubular types of pieces more easily. Just slip the sleeve or pants leg on the free arm as shown above. You will find many uses for this free arm feature such as: 1. Mend elbows and knees of garments more' easily. 2. Sew in sleeves more easily. This is especially true when sewing smaller garments. 3. Applique, embroider or hem around edges of cuffs or pants legs. 4. Sewing in elastic casings in skirts or pants at the waistline. 4O 3. CHECKING PERFORMANCE PROBLEMS WHAT TO DO J:_ m_ •_i_ • ii _z__!ii, _ _i_ i. _ i I _ CARING FOR THE MACH NE ............................................................................................................................... CLEANING AND OILING Fig. 1 Cleaning the feed dogs with a brush. To insure the best possible operation of your machine, it is necessary to keep the essential parts clean at all times. Using a small brush, remove the lint that accumulates in the shuttle Fig. 1 area and around the feed dogs. Fig. 2 Parts of the Shuttle Assembly To Clean the Shuttle Area: 1. This area must be kept free of dust, lint and occasional tangled thread. Raise the needle bar to its highest point and remove the bobbin case. , Push levers of shuttle race aside and lift shuttle race cover and shuttle out. . Clean the shuttle race with small brush, . Put a drop of oil on the center pin of the shuttle and shuttle race. (see arrows) To Replace Shuttle Assembly 1. Position shuttlerace as illUStrated so that shuttle driver is forming half moon on the left side of the machine. . Hold shuttle by center pin and position shuttle so as to form a half moon on the right side, Pointed hook will be on the bottom. = Place shuttle race cover into place over shuttle assembly. 43 OILING UNDER ARM COVER PLATE Remove arm cover plate to oil points indicated in top of machine head. To remove cover plate, insert a screw driver into the spacing between arm casting and top cover plate and lift the cover plate as illustrated below. OILING UNDERSIDE (Free_armtype) Tilt maqhine head back and remove bottom cover to oil points indicated on underside of machine. To remove bottom cover, remove screws (A), (B), (C), (D) and (E) as shown below. /it = OILING UNDERSIDE (Flat-bed type) Tilt machine head back to oil points indicated on underside of machine. < OILING IN FACE cOVER PLATE Swing hinged face cover plate open and oil points indicated in illustration. PART LIST PARTS LIST All parts listed herein may be ordered from any Sears, Roebuck and Co. or Simpsons-Sears Limited store or service center. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION : 1. PART NUMBER 2. PART DESCRIPTION 3. MODEL NUMBER 4. NAME OF ITEM If the parts you need are not stocked locally, your order will be electronically transmitted to a Sears Repair Parts Distribution Center for expedited handling. Ref. No. Part No. Description 1 47 Shuttle 2 38295 Needle plate insert...Zigzag stitch 38296 Needle plate insert...Straight stitch 3 36210 Multi purpose needle plate 4 6510 Bobbin case 5 *6862 Bobbin box with 10 bobbins 6 1939 Bobbin winder rubber ring 7 8286 Thread spool pin 8 2273 Nylon disc 9 *6550 No. 9 needles "6551 No. 11 needles *6552 No. 14 needles *6553 No. 16 needles *6554 No. 18 "needles *6746 Q NEEDLES 10 40390 Standard zigzag foot 11 6870 Satin stitch foot 12 6873 Straight stitch foot 13 6757 Zipper foot 14 40396 Standard zigzag foot 15 37174 Satin stitch foot 16 37175 Straight stitch foot 17 42063 Standard zigz...

Herunterladen

Geben Sie zwei Ziffern: