Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
if the plug does not fit fully in the outlet, one the plug. If it still does not fit, contact a reverse proper outFet Uo qualified electrician to install the the plug in any way. not change Record in space provided below the Serial No. and Model No. of this appliance. I The Serial No. is located Rear of arm. The Model No. is located Rear of arm. Serial No. Model No. 634 0 Retain these numbers for future reference. IMPORTANT SAFETY INSTRUCTIONS safety precautions should always be When using an electrical appliance, basic followed, including the following: Read all instructions before using (this appliance). —To reduce the risk of electric shock: DANGER An appliance should never be left unattended when plugged in. Always unplug this appliance from the electric outlet immediately after using and before cleaning. electric. shock,.. or injwy*tc. persons: Do not allow to be used as a toy. Close attention is necessary when this appliance 1 is used by or near children. Use this appliance only for its intended use as described in this manual. Use only 2 attachments recommended by the manufacturer as contained in this manual, it is not working Never operate this appliance if it has a damaged cord or plug, if 3. has been dropped or damaged, or dropped into water. Return the properly if it appliance to the nearest authorized dealer or service center for examination, repai electrical or mechanical adjustment. Never operate the appliance with any air openings blocked, Keep ventilation open 4. ings of the sewing machine and foot controller free from the accumulation of int, dust, and loose cloth. Never drop or insert any object into any opening. 5. aerosol (spray) products are being used or where oxygen is 8. bni: all controls to the off (“0”) position, then remove plug from rn outlet. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. 9. DANGER Always unplug before relamping. Replace bulb with same type rated 15 watts. 1. Unplug immediately. Do not reach for an appliance that has fallen into water. 2. Do not place or store appliance where it can fall or be pulled into a tub or sink. 3. Do not place in or drop into water or other liquid. WARNING Keep fingers away from all moving parts. Special care is required around the sewing 1. machine needle. Always use the proper needle plate. The wrong plate can cause the needle to break. 2. Do not use bent needles. 3. Do not pull or push fabric while stitching. It may deflect the needle causing it to 4. Switch the sewing machine off ( 0”) when making any adjustments in the needle break. 5. area, such as threading needle, changing needle, or changing presser foot, etc. Always unplug sewing machine from the electrical outlet when removing covers, 6. lubricating, or when making any other user servicing adjustments mentioned in the Never operate on a soft surface such as a bed or couch where the air openings instruction manual. 7. SAVE THESE INSTRUCTIONS CONTENTS 1 1, NAMES OF PARTS 2. OPERATION AND FUNCTION OF PARTS 2 4 3. PREPARATION FOR SEWING 4 3-1. Connecting Power Cord 5 3-2. Setting Telescopic Thread Stand 5 3-3. Changing Threads 6 3-4. Replacing Needle 7 3-5. Threading 4 F-UR THREADQVERLOcksTiTCH USING 2 NEEDLES 10 10 4-i. Bcforc Sewing 10 4-2. Setting the Fabric 10 4-3. Beginning and Ending of Sewing 11 4-4. Adjustment of the Presser Foot Pressure 12 4-5. Thread Tension Chart 13 4-6. Thread Tension Adjustment 5. ADJUSTING BALANCE OF STITCH WIDTH AND CUTTING WIDTH 15 15 6. STITCH LENGTH ADJUSTMENT 16 7. DIFFERENTIAL FEED 17 8. CORDED OVERLOCK 17 9. SEWING FOR CURVED SEAMS 10, THREE THREAD OVERLOCK STITCH USING 1 NEEDLE 18 19 11. ROLLED EDGE 20 12. PIN TUCKS 21 13. REPLACING LOWER CUTTER 21 14. CHANGING LIGHT BULB 21 15. LUBRICATION 23 16. ACCESSORIES 17. TABLE OF SEWING MATERIALS, NEEDLES AND THREADS 24 25 18. PROBLEM SOLVING 26 19. SPECIFICATIONS 27 20. OPTIONAL ACCESSORY PRESSER FEET 1. NAMES OF PARTS 1. Spool pin I2. Thread take up lever cover 3. Pressure regulator screw 4. Thread tension support 5. Telescopic thread stand 6. Thread tension dials 7. Tension release lever 8. Differential feed dial 9. Stitch length dial 10. Presser foot lifter Needle plate 11. Cutting width adjusting dial 12. Presser foot 13. Upper cutter 14. Front cover 15. Cutter cover 16. Front panel 17. Handwheel (Right side of machine) 18. Stitch finger knob 19. Stitch finger —1— 2. OPERATION AND FUNCTION OF PARTS Handwheel Always turn handwheel toward you. + Changing Presser Foot Switch off the machine. 1. Raise presser foot. position by 2. Raise needles to their highest turning handwheel toward you. 3. Push red button A and foot will come off. 4. Position the new foot with the pin right under ankle. Lower presser foot the groove of the lifter so that holder catches the presser toot. Opening Front Cover To open front cover, push part B of cutter cover to right and pull it down toward you. Closing Front Cover Push part B and close it. Always close front cover when sewing. + —2- Cov...
Dieses Handbuch ist für folgende Modelle:Nähmaschinen - BUPEFILDCK 634D (1.04 mb)