Wear goggles, Wear earmuffs Wear a breathing mask The tool must be used only for its prescribed purpose. Any use other than those mentioned in this Manual will be considered a case of misuse. The user and not the manufacturer shall be liable for any damage or injury resulting from such cases of misuse. The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such changes. Even when the tool is used as prescribed it is not possible to eliminate all r

Keep your footing secure and balanced at all times. 12. Look after your tools. Keep tools sharp and clean for better and safer performance. Follow the instructions regarding lubrication and accessory changes. Inspect tool cords periodically and, if damaged, have them repaired by an authorised service facility. Inspect extension cords periodically and replace them if damaged. Keep tool handles dry, clean and free from oil and grease. 13. Disconnect idle tools. Switch off the power and disconnect

The GMC Bench Grinders are designed for light to moderate duty applications in a home environment. They are not intended for use by trade persons. They are ideal for sharpening tools such as drill bits and chisels. The larger tools can be applied to heavier grinding applications on steel sections. All the bench grinders can be fitted with a wire wheel provided that the wheel is rated for use at 3000RPM or higher. 1. MagniVision eye shield 2. Eye shield 3. Grinding wheel 4. Outer guard 5. Spindle

INSTRUCTION MANUAL 150mm (6") 1/2HP / 200mm (8") 3/4HP Bench Grinders • Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris BG612HPL BG834HPL 031222 ED7 DR INSTRUCTION MANUAL 150mm (6") 1/2HP / 200mm (8") 3/4HP Bench Grinders • Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris BG612HPL BG834HPL 031222 ED7 DR Contents Contents Warranty 2 Introduction 3 Environmental protection Description of symbols Spec

Holding and guiding the tool 1. Always clamp the work piece. 2. Do not overload the tool so that the disc slows down. Let the tool do the work rather than applying pressure. The weight of the tool alone provides sufficient pressure. 3. Cutting discs become very hot when in use. Take care not to touch them until they have cooled down. 4. Hold the tool securely and make sure that you have full control at all times. 5. During a cutting operation, maintain an angle of 30 to 40 degrees between the to

• Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris INSTRUCTION MANUAL 1/5 HP / 2/5 HP / 2/3 HP / 1/2 HP Bench Grinders 031222 ED8 DR BG125A BG150A BG200A NTS2000A • Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris INSTRUCTION MANUAL 1/5 HP / 2/5 HP / 2/3 HP / 1/2 HP Bench Grinders 031222 ED8 DR BG125A BG150A BG200A NTS2000A Contents Contents Warranty 2 Introduction 3 Environmental protection 3 Descr

It is strongly recommended that the grinder be firmly mounted to a bench or stand for safe operation. The base of the grinder has a 7mm hole in each corner. These holes accept screws or bolts up to 6mm diameter. Mounting screws are not supplied with the unit. Where the grinder is to be mounted on to a steel work bench, it is advisable to place a piece of timber between the bench and grinder then screw or bolt through the grinder and timber into the bench. This further assists to reduce vibration

If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Connecting to the power supply The GMC Bench Grinders covered in this manual are designed to operate from a standard household supply of 230-240V AC. Prior to plugging in the tool, check the rating label on the rear of the grinder and ensure that it states the tool’s operating voltage is 240V. All the grinders are of Cla

• When sanding wood, always connect the dust extraction filter. • Take special care to guard against harmful and toxic dusts when sanding lead-based painted surfaces, woods and metals, including the following: - All persons entering the work area must wear a mask specially designed for protection against toxic dust and fumes such as those arising from the sanding of lead paint . - Children and pregnant women must not enter the work area. - Do not eat, drink or smoke in the work area. • Before us

This product is warranted for a 2-year period for home domestic use from the date of the original purchase. If found to be defective in materials or workmanship, the tool or the offending faulty component will be replaced free of charge with another of the same item. A small freight charge may apply. The warranty replacement unit is only made available by returning the tool to the place of purchase with a confirmed register receipt. Proof of purchase is essential. We reserve the right to reject