Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
• When sanding wood, always connect the dust extraction filter. • Take special care to guard against harmful and toxic dusts when sanding lead-based painted surfaces, woods and metals, including the following: - All persons entering the work area must wear a mask specially designed for protection against toxic dust and fumes such as those arising from the sanding of lead paint . - Children and pregnant women must not enter the work area. - Do not eat, drink or smoke in the work area. • Before using the sander with metal always remove the extraction filter from the outlet as sparks may ignite the dust or the internal bag. • Do not continue to use worn, torn or heavily clogged sanding sheets. • Do not touch the moving sanding sheet. • Ensure that you have removed foreign objects such as nails and screws from the work before commencing sanding. • Rags, cloths, cord, string and the like should never be left around the work area. Wear goggles Wear ear defenders Wear a breathing mask Accessories • 10 Hook & Loop sandpaper sheets (3x 40, 3 x 60, 2 x 80 & 2 x 120 Grit) • Dust Extraction adaptor • Storage case • Instruction manual Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Switching on and off 1. Connect the plug to the power supply. 2. Push the left-hand side “I” of the sealed on/off switch (1) to start the motor. 3. Push the right-hand side “O” of the sealed on/off switch (1) to stop the motor. 4. Hold the tool securely and make sure that you have full control at all times. Using the sander 1. The sander is designed for sanding wood, metal, plastic and similar materials. It can be used for sanding back and finishing the surface. 2. This sander is a handy size for medium jobs. 3. Wear safety goggles, a dust mask and ear defenders. 4. The whole sanding pad must rest on the workpiece. 5. Switch the sander on while it is placed on the workpiece and move it over the surface to be smoothed in a circular motion. 6. Grip the rear of the handle (2) in one hand and push down on the front of the handle with the other hand. Take care to hold the sander parallel to the work. 7 Use moderate pressure only. 8. If there are still marks on your work after sanding, try either going back to a coarser grade and sanding the marks out before recommencing with the original choice of grit, or try using a new piece of sandpaper to eliminate the unwanted marks before going on to a finer grit and finishing the job. WARNING. Do not use the sander in wet or damp conditions. Fitting a sanding sheet WARNING. Always ensure that the tool is switched off and the plug is removed from the power point before making any adjustments or maintenance procedures. 1. Before fitting sandpaper, remove any dust or debris from the hooks and loops of the base. 2. Match the holes in a suitable sheet with the holes in the base. 3. Simply press the sheet to the base to attach it. 4. To remove the sheet, peel it away from the base. CAUTION. Take care to regularly clean out the build up of dust on the base underneath the sandpaper and not to let the sandpaper wear completely down before replacing it. Failure to observe these two precautionary measures can lead to damage to the hooks and loops on the platen and the sandpaper will not attach properly. 5. Ordinary (non-Hook & Loop type) sanding sheets can also be used. 6. Release the paper clamp (5) from both sides of the sander. 7. Insert the end of the sandpaper under one clamp and pull the paper tight over the base (4) ensuring the holes align with those in the base and then clamp the other side. General Inspection Regularly check that all the fixing screws are tight. They may vibrate loose over time. Power cord maintenance If the supply cord needs replacing, the task must be carried out by the manufacturer, the manufacturer’s agent, or an authorised service centre in order to avoid a safety hazard. Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Type • GMC Product CodeA GMC Service Engineer will take your call and, in most cases, will be able to solve your problem over the phone. You are welcome to use this phone-in service to make suggestions or give comments about any GMC product. With continuing product development changes may have occurred which render the product received slightly different to that shown in this instruction manual. The manufacturer reserves the right to change specifications without notice. Note: Specifications may differ from country to country. The GMC 777 Helpline operates from 7am to 7pm, ...