No ponga la banda sobre el reborde negro que se muestra en la Figura 3. Asegúrese de que las flechas que se encuentran sobre la banda de lijado y sobre la lijadora apunten en la misma dirección. 3. Empuje la palanca hacia atrás para tensar la banda de lijado.

Make sure car surfaces are completely dry before starting to polish the car. NOTE: Do not polish any car in direct sunlight or when the body is hot. 2. Apply Liquid Wax Apply a small amount of liquid wax to the foam pad. Do not start the polisher until the pad is in contact with the car body. Starting the tool without this contact will cause spraying of the wax. NOTE: Too much liquid wax is wasteful and yields no benefit. It is also difficult to remove. 3. Apply To Car Turn the polisher on and m

V ..........................volts A ........................amperes Hz ........................hertz W ......................watts min ......................minutes ......................alternating current ....................direct current no ......................no load speed ........................Class II Construction ........................earthing terminal ........................safety alert symbol .../min ................revolutions or reciprocations per minute CAT. NO. FS500,FS550,F

Also check that the belt doesn’t rub against the belt guide strip shown in figure 6B. Belt life will be greatly increased by keeping the tracking adjustment set properly. Dust Collection BEFORE INSTALLING THE DUSTBAG, UNPLUG THE BELT SANDER. When using your belt sander, dust and grit are produced. It is important to use a dustbag. Connect the dustbag by locating the nozzle of the bag onto the dust collection port of the belt sander as shown in Figure 7 and firmly pushing on using the wire frame

0130M). IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER. KEY INFORMATION YOU SHOULD KNOW: • Never operate the sander without recommended sandpaper properly installed on the base. • Do not push down—let the sander do the work. • Extended drywall sanding is not recommended. SAVE THIS MANUAL FOR FUTURE REFERENCE. VEA EL ESPANOL EN LA CONTRAPORTADA. INSTRUCTIVO DE OPE

3) • Place the sanding base (10) onto the spindle (6). • Place the washer (7) onto the spindle. • Insert the allen screw (8) into the screw hole in the spindle. • Tighten the allen screw using the hex wrench (9) supplied. • To remove the sanding base, remove the allen screw (8) and washer (7). Fitting sanding sheets (Fig. 4) • Detach the two diamond-shaped tips (11) from the sanding sheet (12). • Hold the tool with the sanding base facing upwards. • Place the sanding sheet (12) onto the sanding

• Sanding should be done in a manner to reduce tracking of paint dust outside the work area. CLEANING AND DISPOSAL • All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the sanding project. Vacuum filter bags should be changed frequently. • Plastic drop cloths should be gathered up and disposed of along with any dust chips or other removal debris. They should be placed in sealed refuse receptacles and disposed of through regular trash pick-up procedu

Installing Tool Rests TURN OFF POWER AND DISCONNECT FROM POWER SUPPLY. Hardware bags 5, 6, 7, and the remaining two knobs from bag #1 are used to assemble the tool rests. First install the left side tool rest brackets, as shown in Fig. 4. Next attach the tool rests. Use the bolts, washers, spacers and lock nuts from the plastic bag to secure the brackets and tool rests in place. NOTE: There is a left and right tool rest. When in actual use, the tool rests should be adjusted to within 1/8” of the

IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO THE SUCCESS OF BLACK & DECKER’S QUALITY IMPROVEMENT PROGRAM. KEY INFORMATION YOU SHOULD KNOW: • Always wear eye protection. • Make sure tool rests, spark guards, and eye shields are firmly secured before tool is engaged. SAVE THIS MANUAL FOR FUTURE REFERENCE. VEA EL ESPANOL EN LA CONTRAPORTADA. INSTRUCTIVO DE OPERACION, CENTROS DE

Lubrication MASTER MECHANIC tools are properly lubricated at the factory and are ready for use. Cleaning Blowing dust and grit out of the motor housing using compressed air is a necessary regular maintenance procedure. Dust and grit containing particles from metal grinding often accumulate on interior surfaces and could create an electrical shock hazard if not frequently cleaned out. CAUTION: Never use solvents or other harsh chemicals for cleaning the nonmetallic parts of the tool. Use clean, d