Stimmen - 5, Durchschnittliche Bewertung: 4.2
(
)
)
|
Anleitung Zusammenfassung
Also check that the belt doesn’t rub against the belt guide strip shown in figure 6B. Belt life will be greatly increased by keeping the tracking adjustment set properly. Dust Collection BEFORE INSTALLING THE DUSTBAG, UNPLUG THE BELT SANDER. When using your belt sander, dust and grit are produced. It is important to use a dustbag. Connect the dustbag by locating the nozzle of the bag onto the dust collection port of the belt sander as shown in Figure 7 and firmly pushing on using the wire frame of the dust collection bag. To remove the bag, unplug the belt sander and pull the the plastic nozzle from the dust collection port. WARNING: Collected sanding dust from sanding surface coatings (polyurethane, linseed oil, etc.) can self-ignite in sander dust bag or elsewhere and cause fire. To reduce risk, empty bag frequently and strictly follow sander manual and coating manufacturer's instructions. CAUTION: When working on metal surfaces, do not use the dustbag or a vacuum cleaner because sparks are generated. Wear safety glasses and a dustmask. Due to the danger of fire, do not use your belt sander to sand magnesium surfaces. Do not use for wet sanding. Sanding Lead Base Paint Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the contaminated dust. The greatest danger of lead poisoning is to children and pregnant women. Since it is difficult to identify whether or not a paint contains lead without a chemical analysis, we recommend the following precautions when sanding any paint: Personal Safety • No children or pregnant women should enter the work area where the paint sanding is being done until all clean up is completed. • A dust mask or respirator should be worn by all persons entering the work area. The filter should be replaced daily or whenever the wearer has difficulty breathing. NOTE: Only those dust masks suitable for working with lead paint dust and fumes should be used. Ordinary painting masks do not offer this protection. See your local hardware dealer for the proper (NIOSH approved) mask. • NO EATING, DRINKING or SMOKING should be done in the work area to prevent ingesting contaminated paint particles. Workers should wash and clean up BEFORE eating, drinking or smoking. Articles of food, drink, or smoking should not be left in the work area where dust would settle on them. Environmental Safety • Paint should be removed in such a manner as to minimize the amount of dust generated. • Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils thickness. • Sanding should be done in a manner to reduce tracking of paint dust outside the work area. Cleaning And Disposal • All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the sanding project. Vacuum filter bags should be changed frequently. • Plastic drop cloths should be gathered up and disposed of along with any dust chips or other removal debris. They should be placed in sealed refuse receptacles and disposed of through regular trash pick-up procedures. During clean up, children and pregnant women should be kept away from the immediate work area. • All toys, washable furniture and utensils used by children should be washed thoroughly before being used again. Handy Hints • Always start your belt sander before it is in contact with the workpiece and do not switch it off until after it has been lifted from the workpiece. • Always hold your belt sander with two hands. • Where possible, clamp the workpiece to a work bench or similar sturdy surface. • Use the correct grit sanding belt for your application. The following is a suggested list of belt grits to use with different materials. MATERIAL BELT GRIT Solid Wood 80 Veneer 150 Chipboard 60/80 Plastics 100 Steel 80 (remove dust bag) Paint Removal 40/60 Balsa Wood 100 Acrylic 100 Tool Care And Maintenance Never apply excessive force when you use your belt sander. Too much force can result in an overload and cause damage to the motor or the workpiece. If your belt sander becomes too hot, operate it without load for 2 minutes. Always keep the air cooling vents clear. To clean your belt sander, proceed as follows: BEFORE CLEANING, UNPLUG THE BELT SANDER. • Use a clean dry paint brush to clear vents and ducts. • Clean the housings using a clean damp cloth (do not use solvents, gas or turpentine.) IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts. Accessories Use only 3” x 21” (76 x 533mm) sanding belts. Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory for your tool, please call 1-800-54-HOW-TO (544-6986). CAUTION: The use of any other accessory not recommended for use with this tool could be hazardous. Service Infor...