Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Black & Decker Dateigröße: 3.43 mb Dateiname: Unterrichtssprache:

Use of an extension cable not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and electric shock. PACKAGE CONTENTS The package contains: 1 Angle grinder 1 Side handle 1 Grinding or cutting disc 1 Flange set 1 Two-pin spanner 1 Instruction manual Carefully unpack all parts. OVERVIEW (fig. A) 1. On/off switch 2. Side handle 3. Spindle lock 4. Guard 5. Grinding or cutting disc 13 ENGLISH ASSEMBLY Before attempting any of the following operations, make sure that the tool is switched off and unplugged and that the disc has stopped rotating. Removing and refitting of the guard Never use the tool without the guard, except when sanding. Removing (fig. B) This tool is fitted with a guard. For sanding only, you can remove the guard as follows. Remove the outer flange, disc and inner flange as described below. Use a screwdriver to remove the screws (6). Remove the flange (7), guard (4) and spring washer (8). Store these parts carefully. Refitting (fig. C) Place the tool on a table, with the spindle (9) facing up. Place the spring washer (8) over the spindle and locate it on the shoulder (10). Place the guard onto the tool as shown. Place the flange (11) over the spindle with the protruding pips towards the guard. Make sure that the holes in the flange align with the screw holes. Secure the flange with the screws (6). Make sure that the screws are fully tight and that the guard can be rotated. Fitting the side handle (fig. A) Always use the side handle. Screw the side handle (2) into one of the mounting holes in the tool. Fitting and removing grinding or cutting discs (fig. A, D - G) Always use the correct type of disc for your application. Always use discs with the correct diameter and bore size (see technical data). The maximum thickness for grinding discs is 6 mm, for cutting discs 3.5 mm. Fitting If it has been removed, fit the guard as described above. Place the inner flange (12) onto the spindle (9) as shown (fig. D). Make sure that the flange is correctly located on the flat sides of the spindle. Place the disc (5) onto the spindle (9) as shown (fig. E). If the disc has a raised centre (13), make sure that the raised centre faces the inner flange. Make sure that the disc locates correctly on the inner flange. Place the outer flange (14) onto the spindle. When fitting a grinding disc, the raised centre on the outer flange must face towards the disc (A in fig. F). When fitting a cutting disc, the raised centre on the outer flange must face away from the disc (B in fig. F). Keep the spindle lock (3) depressed and tighten the outer flange using the two-pin spanner (15) (fig. A & G). Make sure that the outer flange is fitted correctly for the type of disc used and that the disc is clamped tightly. Removing Keep the spindle lock (3) depressed and loosen the outer flange (14) using the two-pin spanner (15) (fig. A & G). Remove the outer flange (14) and the disc (5). Fittingandremovingsandingdiscs(fig.A,H&I) For sanding, a backing pad is required. The backing pad is available from your Black & Decker dealer as an accessory. 14 ENGLISH Fitting Remove the guard as described above. Place the inner flange (12) onto the spindle (9) as shown (fig. H). Make sure that the flange is correctly located on the flat sides of the spindle. Place the backing pad (16) onto the spindle. Place the sanding disc (17) onto the backing pad. Place the outer flange (14) onto the spindle with the raised centre facing away from the disc. Keep the spindle lock (3) depressed and tighten the outer flange using the two-pin spanner (15) (fig. A & I). Make sure that the outer flange is fitted correctly and that the disc is clamped tightly. Removing Keep the spindle lock (3) depressed and loosen the outer flange (14) using the two-pin spanner (15) (fig. A & I). Remove the outer flange (14), the sanding disc (17) and the backing pad (16). After sanding, refit the guard on the tool. USE Let the tool work at its own pace. Do not overload. Carefully guide the cable in order to avoid accidentally cutting it. Be prepared for a stream of sparks when the grinding or cutting disc touches the workpiece. Always position the tool in such a way that the guard provides optimum protection from the grinding or cutting disc. Wear safety glasses or goggles when operating this tool. Switching on and off (fig. J) To switch on, slide the on/off switch (1) forward. Note that the tool will continue running when you release the switch. To switch off, press the rear part of the on/off switch. Hints for optimum use Firmly hold the tool with one hand around the side handle and the other hand around the motor housing (fig. K). When grinding, always maintain an angle of approx. 15° between the disc and the workpiece surface (fig. L). MAINTENANCE Your Black & Decker tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regul...

Herunterladen

Geben Sie zwei Ziffern: