Stimmen - 4, Durchschnittliche Bewertung: 3
(
)
)
|
Fotos und technische Daten Makita BO5020 |
Anleitung Zusammenfassung
Higher speed is obtained when the dial is turned in the direction of number 5; lower speed is obtained when it is turned in the direction of number 1. 003291 Refer to the figure for the relationship between the number 003291 Refer to the figure for the relationship between the number C range: For regular sanding 12000 NOTE: • The figure shows standard applications. They may differ C 4000 B under certain conditions. A CAUTION: 45 • If the tool is operated continuously at low speeds for a long time, the motor will get overloaded, resulting in tool malfunction. • The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 003296 Front grip Install the front grip on the tool so that its protrusions fit into the matching notches in the front of the tool. Secure the front grip using a screwdriver to tighten the screw through the hole in the front grip. Orbits per minute 123 Dial setting 43 1 2 1. Notches 2. Front grip 3. Screwdriver 4. Hole in front grip 003301 Installing or removing abrasive disc CAUTION: • Always use hook-and-loop system abrasive discs. Never use pressure-sensitive abrasive discs. To install the abrasive disc, first remove all dirt or foreign matter from the pad. Then attach the abrasive disc to the pad, using the hook-and-loop system of the abrasive disc and the 1 2 1 2 Push button 2. Dust nozzle 1 2 1. Dust nozzle 2. Push button 1. Hook 3 12 4 003325 2. Dust nozzle 3. Push button 4. Dust bag pad. Be careful to align the holes in the abrasive disc with those in the pad. 003322 Installing dust bag Install the dust bag on the tool so that the arrow with “UP” indicated on the dust nozzle points upward. 003324 Emptying dust bag When the dust bag is about half full, switch off and unplug the tool. Hold the tool and remove the dust bag from the dust nozzle while pressing the push button. 003327 After emptying the dust bag, insert the hook on the dust nozzle into the rectangular hole on one side of the dust bag frame and push up the dust bag frame until it clicks into place on the push button. OPERATION OPERATION Sanding operation CAUTION: • Never run the tool without the abrasive disc. You may seriously damage the pad. • Never force the tool. Excessive pressure may decrease the sanding efficiency, damage the abrasive disc or 1 1. Sponge pad shorten tool life. Hold the tool firmly. Turn the tool on and wait until it attains full speed. Then gently place the tool on the workpiece surface. Keep the pad flush with the workpiece and apply slight pressure on the tool. Polishing operation CAUTION: • Use only a Makita genuine sponge pad, felt pad or wool pad (optional accessories). • Always operate the tool at low speed to prevent work surfaces from damage/burning. • Never force the tool. Excessive pressure may decrease the polishing efficiency and cause motor overload, resulting in tool malfunction. 003339 Applying wax Use an optional sponge pad. Apply wax to the sponge pad or work surface. Run the tool to smooth out wax. NOTE: • First, wax a non critical portion of the work surface to make sure that the tool will not scratch the surface or result in uneven waxing. 003341 Removing wax Use an optional felt pad. Run the tool to remove wax. 1 1. Felt pad 003343 1 003343 1 1. Wool pad MAINTENANCE ACCESSORIES Polishing Use an optional wool pad. Run the tool and apply the wool pad gently to the work surface. CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. • Hook-and-loop type abrasive discs (with pre-punched holes) • Hook-and-loop type sponge pad • Hook-and-loop type wool pad • Hook-and-loop type felt pad Memo Memo Memo Cut Cut s Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: Home Center Other ( Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply 2. Use of the product is intended for: Construction Trade Industrial Maintenance Home Maintenance Hobby Other ( ) 5. Any comments: 3. How did you learn abou...