Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Box 1468 Racine, Wisconsin 53401 1-800-437-3635 Voir page 12 .Habla espanol? Vea pagina 23 © Robert Bosch Tool Corporation 1997 all rights reserved DM 2610919361 9/03 9/5/03 8:33 AM Page 2 Power Tool Safety Rules injury. Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal SAVE THESE INSTRUCTIONS ! WARNING Work Area Damaged cords increase the risk of electric Keep your work area clean and well lit. shock. Cluttered benches and dark areas invite When operating a power tool outside, use accidents. an outdoor extension cord marked "W-A" Do not operate power tools in explosive or "W." These cords are rated for outdoor atmospheres, such as in the presence of use and reduce the risk of electric shock. flammable liquids, gases, or dust. Power Refer to “Recommended sizes of Extension tools create sparks which may ignite the Cords” in the Accessory section of this dust or fumes. manual. Keep by-standers, children, and visitors Personal Safety away while operating a power tool. Stay alert, watch what you are doing and Distractions can cause you to lose control. use common sense when operating a power tool. Do not use tool while tired or Electrical Safety under the influence of drugs, alcohol, or Double Insulated tools are equipped with medication. A moment of inattention while a polarized plug (one blade is wider than operating power tools may result in serious the other.) This plug will fit in a polarized personal injury. outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it Dress properly. Do not wear loose still does not fit, contact a qualified clothing or jewelry. Contain long hair. electrician to install a polarized outlet. Do Keep your hair, clothing, and gloves away not change the plug in any way. Double from moving parts. Loose clothes, jewelry, Insulation eliminates the need for the or long hair can be caught in moving parts. three wire grounded power cord and Keep handles dry, clean and free from oil grounded power supply system. Before and grease. plugging in the tool, be certain the outlet Avoid accidental starting. Be sure switch voltage supplied is within the voltage marked is “OFF” before plugging in. Carrying tools on the nameplate. Do not use “AC only” with your finger on the switch or plugging in rated tools with a DC power supply. tools that have the switch “ON” invites Avoid body contact with grounded accidents. surfaces such as pipes, radiators, ranges Remove adjusting keys or wrenches and refrigerators. There is an increased before turning the tool “ON”. A wrench or risk of electric shock if your body is a key that is left attached to a rotating part of grounded. If operating the power tool in the tool may result in personal injury. damp locations is unavoidable, a Ground Do not overreach. Keep proper footing Fault Circuit Interrupter must be used to and balance at all times. Proper footing supply the power to your tool. Electrician’s and balance enables better control of the rubber gloves and footwear will further tool in unexpected situations. enhance your personal safety. Use safety equipment. Always wear eye Don't expose power tools to rain or wet protection. Dust mask, non-skid safety conditions. Water entering a power tool will shoes, hard hat, or hearing protection must increase the risk of electric shock. be used for appropriate conditions. Do not abuse the cord. Never use the cord to carry the tools or pull the plug Tool Use and Care from an outlet. Keep cord away from Use clamps or other practical way to heat, oil, sharp edges or moving parts. secure and support the workpiece to aReplace damaged cords immediately. stable platform. Holding the work by hand -2 DM 2610919361 9/03 9/5/03 8:33 AM Page 3 or against your body is unstable and may other condition that may affect the tools lead to loss of control. operation. If damaged, have the tool serviced before using. Many accidents are Do not force tool. Use the correct tool for caused by poorly maintained tools. Develop your application. The correct tool will do a periodic maintenance schedule for your the job better and safer at the rate for which tool. it is designed. Use only accessories that are Do not use tool if switch does not turn it recommended by the manufacturer for “ON” or “OFF”. Any tool that cannot be your model. Accessories that may be controlled with the switch is dangerous and suitable for one tool, may become hazardous must be repaired. when used on another tool. Disconnect the plug from the power source before making any adjustments, Service changing accessories, or storing the tool. Tool service must be performed only by Such preventive safety measures reduce the qualified repair personnel. Service or risk of starting the tool accidentally. Store maintenance performed by unqualifiedidle tools out of reach of children and personnel could result in a risk of injury. For ...