Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
The HP MSR SBM is an HP MSR application running on a HP MSR Open Architecture Platform (OAP) Module. The module is installed in an HP MSR 30 Series or MSR 50 Series Router at the branch office. The HP MSR SBM includes a Windows Server 2008 R2 that runs as the base OS. Running on this server, is a Microsoft Lync Server 2013 Survivable Branch Appliance that integrates with the main office Standard or Enterprise Lync Server Pool and handles services for the branch office. The HP MSR SBM provides survivability; if the WAN connection to the main office data center fails, the HP MSR SBM routes all calls over its public switched telephone network (PSTN) connection. The HP MSR SBM is managed through an easy to use Web browser interface. The Windows Server 2008 R2 OS running on the module can also be accessed with Remote Desktop. Module hardware Figure 1 MIM-OAPS module front panel LEDs and ports (1) USB port (2) 100/1000Base-T Ethernet port LED (3) LINK/ACT LED for the GigabitEthernet port (4) Standby button (5) System status LED (SYS) (6) Disk LED (DISK) (7) GigabitEthernet port 7 1 2 3 6 5 4 2 Figure 2 MIM-OAP module front panel LEDs and ports (1) USB port (2) 100/1000Base-T Ethernet port LED (3) LINK/ACT LED for the GigabitEthernet port (4) Standby button (5) System status LED (SYS) (6) Disk LED (DISK) (7) GigabitEthernet port Figure 3 FIC-OAP module front panel LEDs and ports (1) 100/1000Base-T Ethernet port LED (2) LINK/ACT LED for the GigabitEthernet port (3) Standby button (4) System status LED (SYS) (5) Disk LED (DISK) (6) GigabitEthernet port (7) USB port Table 1 GigabitEthernet management port specifications Item Specification OAP OAPS Connector type RJ-45 Port type MDI/MDIX auto-sensing Port transmission rate • 10/100 Mbps, half/full duplex • 1000 Mbps, half duplex Frame format Ethernet_II Ethernet_SNAP Table 2 Maximum OAP modules Router model FIC-OAP modules MIM-OAP modules MIM-OAPS modules MSR 30-10 0 0 1 7 1 2 3 6 5 4 3 Router model FIC-OAP modules MIM-OAP modules MIM-OAPS modules MSR 30-11 0 0 1 MSR 30-11E 0 0 1 MSR 30-11F 0 0 1 MSR 30-16 0 1 1 MSR 30-20 0 1 1 MSR 30-40 0 1 2 MSR 30-60 0 1 2 MSR 50-40 2 (without any other module installed) 0 0 MSR 50-60 2 (without any other module installed) 0 0 MSR 50-40 (two power modules) 4 (without any other module installed) 0 0 MSR 50-60 (two power modules) 4 (without any other module installed) 0 0 NOTE: The value 0 in Table 1 indicates that the router does not support the module. Module software Updating the router software If you need to install the HP MSR router software that will house your module, see MSR Software Release Notes or at Installing the HP MSR SBM CAUTION: • To avoid Lync SBM host exception, shut down the Lync SBM host before you unplug the FIC-OAP module when the HP MSR50 router is powered on. • To avoid Lync SBM host exceptions, shut down the Lync SBM host and turn off the HP MSR30 router before you remove the MIM-OAP or MIM-OAPS module. Installation precautions • Static electricity can severely damage the electronic components on the module. When handling and installing the module, follow these procedures to avoid damage from static electricity: .. Handle the module by its bulkhead or edges and avoid touching the components and the circuitry on the board. 4 .. When installing the module, equalize any static charge difference between your body and the router by wearing a grounding wrist strap and attaching it to the router's metal body, or by frequently touching the router’s metal body. • The module has "low-force, high-performance" connectors. High insertion forces are not necessary to install the module, and should not be used. • Make sure the module is fully inserted. Press the module into the slot until the bulkhead on the module contacts or is very close to contacting the front face of the router chassis. • Once the module is fully inserted, screw in the two retaining screws to secure the module in place. • For safe operation, proper router cooling, and reduction of electromagnetic emissions, make sure a slot cover is installed on any unused module slot. For safety, no more than one slot should be uncovered at a time, even temporarily, when the router is powered on. Check the temperature specifications for the module; different modules have different temperature requirements. • HP OAP modules fall into three categories: FIC-OAP modules (for HP MSR50 routers), MIM-OAP modules (for HP MSR30 routers), and MIM-OAPS modules (also for HP MSR30 routers). FIC-OAP modules are hot-swappable. You can install or remove a FIC-OAP module while the HP MSR50 router is on. The MIM-OAP module and MIM-OAPS module are not hot-swappable. You must turn off the HP MSR30 router before installing or removing the MIM-OAP or MIM-OAPS module. CAUTION: • To avoid Lync SBM host exception, shut down the Lync SBM host before you unplug the FIC-OAP module when the HP MSR50 router is powered on. • To avoid Lync SBM host exceptions, shut do...