Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Step 7 For the Subnet Mask and Default Gateway fields, enter the same number as the TCP/IP setting of your computer. Step 8 Click OK. Step 9 Close the PS Utility program. 7 5. Verifying Network Connection Step 1 Run the PS Utility by going to Start, (All) Programs, PS-Utility, PS-Utility v3.00. Step 2 Make sure the Print Server is detected under the Device Name. Step 3 Click on Show Web Setup to display the Print Server’s Web Configuration Utility. Step 4 Click on the Printer Information link and make sure the Printer Status displays On line. 8 Step 5 Click on the Print Test link and click the Test button. The Print Server will perform a low-level print test, bypassing the operating system layer. Note: Your printer should print out a test page. If not, verify that the printer is powered on and all cables are securely connected and try again. If the printer still fails to print a test page, please check the printer compatibility list on our web site at for a list of compatible printers. If your printer is not on the list, it may not be compatible with the Print Server. Step 6 Once the printer successfully prints out a test page, you may close the web browser and proceed to the next section. 9 6. Running PS Wizard Warning: Make sure you have installed the printer driver locally on every computer that will use the print server in your network before running the PS Wizard. Otherwise, the PS Wizard will not run properly. Be sure to run the PS Wizard on all the computers that will use the print server in your network. Step 1 Insert the provided CD and wait for the autorun screen to appear. Step 2 Click on Run PS Wizard. Note: If the autorun screen does not appear automatically, go to Start, Run, type D:\autorun.exe (where D is the letter of your CD drive) and click OK. 10 Step 3 Click Next. Step 4 Select the printer that is connected to the Print Server and click Next. 11 Step 5 Double-click on the Print Server Name, select the Printer Port Name, and click Next. Step 6 Click Finish and OK. (For Windows 95/98/ME, you’ll need to reboot the computer). Step 7 Run the PS Wizard on all the computers in your network that will use the Print Server. 12 7. Performing Operating System Print Test The final step in setting up the Print Server is to perform an operating system print test. Please note that the instructions below are for Windows XP, but the steps are similar for all the other Windows operating systems. Step 1 Click on Start, Settings, Printers and Faxes. Step 2 Right-click on the printer that is connected to the Print Server and select Properties. 13 Step 3 Click on the Print Test Page button. Windows should print out a test page. You have successfully configured the Print Server for printing. 14 8. Using the PS Utility PS Utility is a user-friendly program that allows you to configure some basic functions of the Print Server such as performing a factory reset or updating the firmware. To access the complete management features of the Print Server, you’ll need to use the Web Configuration Utility, which is described in the next section. Note: If you haven’t installed PS Utility yet, please follow the installation instructions as described in Section 3, Installing PS Utility. You can start PS Utility by going to Start, (All) Programs, PS-Utility, PS-Utility v3.00. Device Name: Lists any Print Server that is connected on your network. Discover Device: Click on this button to automatically search for any Print Server that is connected to your network. Setup Wizard: Click on this button to run the setup wizard for the Print Server. Change IP Address: Click on this button to change the IP Address and other TCP/IP settings for the Print Server. Show Web Setup: Click on this button to display the Web Configuration Utility. Update Firmware: Click on this button to update the Print Server’s firmware. Note: You must download the updated firmware from first. Factory Reset: Click on this button to reset the Print Server back to factory settings. Print Test: Click on this button to perform a print test. About: Click on this button to display the version number of the PS Utility. Close: Click on this button to close PS Utility. 15 9. Using the Web Configuration Utility The Web Configuration Utility allows you to manage the full features of the Print Server with an easy-to-use user interface. You can start the Web Configuration Utility in two ways: 1. Click on the Show Web Setup button in PS Utility. or 2. Open your web browser, type in the IP address of the Print Server in the URL address field, and press Enter. (Default IP address is 192.168.1.254). The Web Configuration Utility will display the Management, System page. Click on any of the links at the left to display the corresponding page. 16 9.1 Home The Home page displays the status of your Print Server. Click Refresh to update the page. 17 9.2 Setup Wizard The Setup Wizard page allows you to configure some basic settings of the Prin...