Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Delta, modell SERIN 2064.4

Hersteller: Delta
Dateigröße: 698.39 kb
Dateiname: Install_1776.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 2 3 1 Tighten LOCKNUT (1) firmly with Adjustable Wrench or Channel Locks. 2 INSTALL DRAIN FROM BELOW FIXTURE 6 From under side of BIDET install DRAIN BODY (1) up through drain outlet. Note: No plumber’s putty or caulk is required. The CABLE ATTACHMENT POINT (2) must face towards the rear of the BIDET. DRAIN OUTLET Install FOAM GASKET (3) and FLANGE (4) onto drain body from above BIDET and tighten FLANGE (4) firmly. 1 4 3 4 Fig. B. Fig. A. Fig. B. 2 3 1 Fig. A. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. DRAIN BODY 4 M968924 Rev.1.3 Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. 10 Connect water supply to VALVE BODIES (7,7a) with 1/2" IPS FLEXIBLE SUPPLIES (8) or 3/8" O.D. BULL-NOSE RISERS (9). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length. TEE AND HOSE CONNECTION NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY. HOT COLD FLEXIBLE SUPPLIES 1 1/2" PIPE THREAD 3/8 COMPRESSION CONNECTION 2 POP-UP KNOB (1) must be fully down. Fig. A. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. B. Your new POP-UP DRAIN installation is now complete. Fig. C. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. C. Fig. B. ATTACH CABLE CONNECTOR 8 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. CHECK OPERATION OF POP-UP INSTALL DIVERTER KNOB 9 Fig. C. 1-1/4” O.D. 1 1 5 3 1 2 2 WATER SUPPLY CONNECTION Insert SEAL (1) into ADAPTER (2) and tighten ADAPTER (2) to side of TRANSFER VALVE (3). Install SEAL (4) into coupling nut of TEE (5) and tighten connection to ADAPTER (2). Connect HOSE COUPLING NUTS (6) to Hot and Cold valve bodies and securely tighten. 7 6 7a 6 Front 9 Push DIVERTER KNOB (1) onto HANDLE ADAPTER (2). Push on RING (3) and tighten with SCREW (4). Press on KNOB CAP (5). Note: Screwdriver gap is for disassembling and should point downwards. 4 2 COMPRESSION NUT COUPLING NUT OUTLINE OF BIDET 3/8 O.D. BULL-NOSE RISERS CONNECT TO WASTE OUTLET 2 3 4 5 FERRULE DOWN Fig. A. M968924 Rev.1.3 CHECK DRAIN CONNECTIONS 12 11 13 14 15 TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Operate both HANDLES (1) to flush water lines thoroughly. Rotate TRANSFER VALVE (5) from rim wash to spray several times to check operation. SERVICE Pull up POP-UP KNOB (3) and fill Bidet with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Bidet. If STOPPER (4) does not seal properly, please refer to “Troubleshooting Guide” in these instructions. Push POP-UP KNOB (3) down and check all drain connections...