Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Hans Grohe Dateigröße: 698.39 kb Dateiname: Install_1776.pdf Unterrichtssprache:

Replace UPPER GASKET (8) and WASHER (7) and ESCUTCHEON (6) until it locks against internal stop. Position the side threaded outlet rearward and secure MOUNTING NUT (11). Remove ESCUTCHEON (6), WASHER (7) and UPPER GASKET (8) from TRANSFER VALVE (9). Insert TRANSFER VALVE (9) into the center forward hole of BIDET. HOT COLD BIDET LEDGE 10 4 3 3a 8 9 1 5 2 6 Roughing-in Dimensions 2 SPRAY INSTALLATION Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside of SPRAY BODY FLANGE (2) and secure with NUT (3). Thread SPRAY CAP (9) onto SPRAY BODY (1). Thread SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY BODY (1). Connect other end of HOSE (4) with SEAL WASHER (6) to side outlet NIPPLE (7) of the TRANSFER VALVE (8). PUTTY 6 2 7 8 1 9 Tighten LOCKNUTS (1) with WRENCH (5) (supplied) to secure VALVE BODIES (3, 3a). Install LOCKNUT (1) and RUBBER WASHER (2) onto VALVE BODIES (3, 3a). From under side of mounting surface, install VALVE BODY (3, 3a) through valve mounting holes. Threads of VALVE BODY (3, 3a) should extent at least 5/16 of a inch above mounting surface top. Fig. A. Thread ESCUTCHEON (4) onto VALVE BODIES (3, 3a) until snug against internal stop. If necessary, adjust LOCKNUT (1). Place RUBBER RING (10) into ESCUTCHEON (4). MOUNTING SURFACE 4 10 21 3, 3a 5/16'' MIN. Fig. A. 11 Adjustable Wrench Screwdriver Channel Locks Recommended tools Tubing Cutter Phillips Screwdriver Plumbers' Putty or Caulking BIDET OUTLINE IS SYMBOLIC FINISHED FLOOR FINISHED WALL 1-1/4 O.D. TAILPIECE DOUCHE SPRAY 2-1/8 DIA. ADJ. 1-1/4 TO 2-1/4 3-7/8 5-1/2 1-3/8 DIA. 7/8 DIA. 1-1/4 MAX. 1-3/16 DIA. 2-1/4 (C) (H) DIA. 4-1/4 FOR GROUND JOINT CONNECTION OR 1/2 " O.D. SLIP (INLETS) REAR VIEW WITH WALL REMOVED TRANSFER VALVE (FOR FLUSHING RIM OR SPRAY) 8 TO 12 7 To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. *Your new American Standard faucet is designed to work only with the Speed Connect drain. Speed Connect Drain* • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. M968924 Rev.1.3 POP-UP DRAIN Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 7 3 5 4 FLANGE GASKET Check DRAIN FLANGE in BIDET to ensure that WHITE FOAM GASKET (1) is fully compressed and not visible. Fig. A. DRAIN FLANGE 1WHITE FOAM GASKET NOT VISIBLE Insert LIFT ROD GUIDE (1) and CABLE CONNECTOR (2) through rear hole, making sure SEAL WASHER (3) is properly seated. Fig. B. From below slip slot in MOUNTING NUT (4) over CABLE (5). Thread NUT (4) onto lift rod guide shank to secure ROD GUIDE (1) to bidet. Hand tighten only. Fig. B. 1 2 4 3 ILLUSTRATION SHOWN LESS VALVES SLOTTED MOUNTING NUT POP-UP ROD ASSEMBLY TIGHTEN LOCKNUT 1 Fig. A. Fig. B. REMOVE FLANGE Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 2 3 1 Tighten LOCKNUT (1) firmly with Adjustable Wrench or Channel Locks. 2 INSTALL DRAIN FROM BELOW FIXTURE 6 From under side of BIDET install DRAIN BODY (1) up through drain outlet. Note: No ...

Herunterladen

Geben Sie zwei Ziffern: