Login:
heruntergeladen wurde: 1   Dateigröße: 121 kb   Hersteller: Wayne  
Kategorie: Plumbing
@name

If the power source is out of sight, lock and TAG IN OPEN (OFF) POSITION to prevent unexpected power application. Failure to do so could result in fatal electrical shock! This unit is not designed for use in septic tanks or underground vaults to pump raw sewage or effluents. Never use in hazardous or explosive locations. 1. This pump has been designed to attach to a standard garden hose. Thread the female end of the garden hose to the male discharge on the pump. 2. To reduce leakage between the

heruntergeladen wurde: 1   Dateigröße: 835 kb   Hersteller: Wayne  
Kategorie: Plumbing
@name

2. Disassembly of the motor prior to expiration of warranty will void the warranty. If repairs are required, see troubleshooting chart. 3. Inlet should be kept clean and free of all foreign objects and inspect annually. A clogged inlet will damage pump. 4. Pump should be checked monthly for proper operation. This pump contains dielectric oil for cooling. This oil can be harmful to the environment. Check the state environmental laws before disposing this oil. Figure 6 - Duplex System Off Level On

heruntergeladen wurde: 6   Dateigröße: 835 kb   Hersteller: Wayne  
Kategorie: Plumbing
@name

Cutting the cord or plug will void the warranty and make the pump inoperable. Figure 4 - Typical Installation Three prong grounded outlet equipped with a ground fault interruptor Main waste line to sewer or septic tank 2 in. Discharge pipe Upper level drainage Cleanout Pump Float Switch Flange Floor drain Dryer Washer Laundry tubs Vent pipe Lavatory Shower Washer drain 45° Elbow 2 in. Check valve 2 in. gate valve Operating Instructions and Parts Manual Union Operating Instructions and Parts Manu

heruntergeladen wurde: 2   Dateigröße: 835 kb   Hersteller: Wayne  
Kategorie: Plumbing
@name

All models with a plug-in power cords system should still have a qualified electrician inspect the outlet being used to ensure proper wiring. Grounding Grounded Blade Outlet Power Cord Switch Cord Figure 3 TESTRESET The control switch is a wide-angle system which prevents short cycling of the pump motor and the consequential problems that short cycling can cause. The switch can be mounted on the discharge pipe (just above the pump discharge flange). See illustrations for switch mounting arrangem

heruntergeladen wurde: 6   Dateigröße: 835 kb   Hersteller: Wayne  
Kategorie: Plumbing
@name

11 1/2 in. high x 9 3/4 in. base 2 in. NPT (Adapter included) REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping. © 2009 Wayne Water Systems For parts, product & service information 332200-001 2/09 visit Operating Instructions and Parts Manual General Information Sewage Pump Systems: Simplex System A simplex system consists of one pump, its control switch, and one basin. It is used in applications where less than six toilets (un

heruntergeladen wurde: 6   Dateigröße: 655 kb   Hersteller: Wayne  
Kategorie: Plumbing
@name@name@name

13-1/2 inch x 11 inch Intake ................................................. 2 inch Performance Discharge............................................ 2 inch NPT female, 3 inch NPT male Cut-in level (factory set)....................18 inch Cut-out level (factory set) ................. 10 inch GALLONS PER hOuR At tOtAL hEAD IN fEEt Model 10 15 200 SEL40 3700 1350 Differential......................................... 8 inch SEL50 6420 4200 1500 Switch..............................................

heruntergeladen wurde: 6   Dateigröße: 655 kb   Hersteller: Wayne  
Kategorie: Plumbing
@name@name@name

angle with the valve pivot on top. In a vertical position, solids will tend to lodge on the valve flapper and can prevent it from opening. 3. Drill a 1/8 inch hole in the discharge pipe approximately 1 inch to 2 inch above the pump discharge when a check valve is used. The hole prevents air locking of the pump at the initial start-up and if it should lose prime. 4. A gate valve should be installed in the system after the check valve. This gate valve should be a full port valve which will pass 2

heruntergeladen wurde: 3   Dateigröße: 4 mb   Hersteller: Wayne  
Kategorie: Plumbing
@name@name@name

Water level too low 2. Blown fuse or tripped circuit breaker 3. Low line voltage 4. Defective motor 5. Defective float switch 6. Impeller (pump filled with debris) 7. Tangled switch 8. Insufficient liquid level 1. Pump switch will not turn on unless water covers top of pump 2. If blown, replace with proper sized fuse or reset breaker 3. If voltage is under recommended minimum, check wiring size from the main switch on property. If OK, contact power company. 4. Return for service or replace motor

heruntergeladen wurde: 0   Dateigröße: 880 kb   Hersteller: Wayne  
Kategorie: Plumbing
@name@name@name

Check valve 45. Vent Inlet Gasket 1/2 inch Min. Clearance Basin Figure 3 - Prefabricated Basins 7. When a tether switch is used, rigid discharge pipe is required. If the pump is allowed to move, the tether switch could be restricted by the basin wall, preventing the pump from operating. Before removing pump from basin for service, always disconnect electrical power to pump and control switch. For any work on pump or switch, ALWAYS unplug the power cord. Do not just turn off circuit breaker or un

heruntergeladen wurde: 0   Dateigröße: 256 kb   Hersteller: Wayne  
Kategorie: Plumbing
@name@name@name

Low line voltage 2. Debris caught in impeller or discharge 3. Worn or defective pump parts or plugged impeller 4. Pump running backwards 5. Pump not properly sized for application 6. Check valve stuck closed or installed backwards 7. Shut off valve closed 1. If voltage is under recommended minimum, check wiring size from the main switch on property. If OK, contact power company 2. Remove, clean and check for tightness 3. Replace entire pump. Clean parts if required 4. Check rotation. (CCW from b





Kategorien