Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
2 Wall Shower Components .................... 2 Wall Shower Dimensions ..................... 3 Step 1: Rough-In Piping ...................... 3 Step 2: Install Shower ........................ 3 Vertical Shroud Installation ................... 4 Horizontal Shroud Installation ................4 Table des Matieres Fournitures requises ......................... 5 Hauteurs de douche conseillees .............. 5 Elements de la douche ......................5 Dimensions de la douche .................... 6 Etape 1 : Tuyauterie de raccordement ......... 6 Etape 2 : Pose de la douche .................. 6 Pose de gaine verticale ...................... 7 Pose de gaine horizontale .................... 7 Contenido Materiales necesarios ....................... 8 Alturas recomendadas de la ducha ...........8 Componentes de la ducha de pared .......... 8 Dimensiones de la ducha de pared ........... 9 Paso 1: Colocacion de tuberias empotradas . . . 9 Paso 2: Instalacion de la ducha ............... 9 Instalacion vertical del recubrimiento ......... 10 Instalacion horizontal del recubrimiento ...... 10 215-1441 Rev. C EN 07-304 P.O. Box 309, Menomonee Falls, WI 53052-0309 © 2007 Bradley Corporation Phone: 1-800-BRADLEY Fax: 262-253-4161 Page 1 of 10 4/2/07 WS-1X Installation IMPORTANT! Read this entire installation manual to assure proper installation. When finished with the installation, file this manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances is the responsibility of the installer. Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not begin installation until you obtain the missing parts. Make sure that all water supply lines have been flushed and then completely turned off before beginning installation. Debris in supply lines can cause valves to malfunction. Product warranties may be found under “Product Information” on our web site at Installation THISSIDE UP Packing List Supplies Required Recommended Shower Heights • Water supply piping to connect 1/2" NPT flexible hose(s) • Suitable wall anchors and 1/4" diameter fasteners to mount shower to the wall • Pipe Sealant Shower Components Age Male Female Adult 6'0" (1.83m) 6'0" (1.83m) Teenage 6'0" (1.83m) 5'6" (1.68m) Pre-Teens 5'6" (1.68m) 5'6" (1.68m) Supplies thru-wall Supplies from above 4/2/07 Bradley Corporation • 215-1441 Rev. C; EN 07-304 Installation WS-1X 1 Rough-In Piping Supply inlets are 1/2" NPT flexible hose and are accessible from the back of the shower or from knockouts on the top cover. Bradley’s Equa-Flo valve shown; other valve versions install in similar manner. • If supplies will be run “thru-wall”, Bradley recommends using a 90° street ell to connect the supply hoses. • If supplies will be run “from above”, Bradley recommends running them approximately 1/2" into the top cover. See table on page 2 for recommended showerhead heights. 2 Install Shower Shower Dimensions Front Rear Hot Cold or Tempered SuppliesThru Wall 6-3/4" (173) 4" (102) 1/2" (13)5" (127) 6" (152) 4" (102) 13-3/4" (349) 3-1/8" (80) Supplies from above 22-3/4" (579) Using the shower hinge as a template, mark wall and drill holes for 1/4" fasteners (wall anchors and fasteners supplied by installer). Secure hinge side to the wall. A Connect the 1/2" flexible hoses to the supply lines. Turn the water on and check for leaks and adequate water spray. B Close the shower tight to the wall and mark the holes for the mounting tabs on the wall. mark wall and drill holes for 1/4" fasteners. Secure tabs to the wall. C 3-1/4" (82) 1/2" (12) 17-3/4" (452) 6-7/8" (173) 1/2" (12) 1-3/4" (44) 3-1/2" (89) 16-3/4" (425) Bradley Corporation • 215-1441 Rev. C; EN 07-304 4/2/07 Installation WS-1X Vertical Shroud Installation (165mm) 6-1/2" 6-1/2" (165mm) 3/4"CEILING LINE (19mm) Position the slip ring (186-1358) against the wall at the ceiling B and in line with the shroud bracket. Secure the slip ring to the wall with 1/4" fasteners. Position the shroud mounting bracket (140-904) on the wall Aabove the shower. Secure the bracket to the wall with 1/4" fasteners (wall anchors and fasteners supplied by installer). 3" (76mm) 6-5/8" (168mm) 4" (102mm) C C Position the shroud and secure with the fasteners provided. Using the holes in the top of the shroud as a template, drill and tap #10-24 holes in the slip ring with a .149 drill bit. Secure the shroud to the slip ring. #10-24 SCREW (160-138) SHOWER (4) PLACES Horizontal Shroud Installation 4 4/2/07 Bradley Corporation • 215-1441 Rev. C; EN 07-304 Secure the brackets to the wall with 1/4” diameter fasteners (wall anchors and fasteners supplied by installer). A Using the horizontal shroud as a guide, secure the slip ring to the wall with 1/4" diameter fasteners. B Using the shroud as a template, drill and tap #10-24 holes in the slip ring with a .149 drill bit.C CORNER LINE Ins...