Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
DESCRIPTION 1 3-1905 TOOL BAR (2) 2 4-7857 CLEVIS, Bracket 3 3-2474 SHANK, Cultivator (4) 4 3-1904 CLAMP (4) 5 1-2244 SHOVEL, Double Point (4) 6 3-2473 ADAPTER, Harrow 7 4-7858 DRAW-BAR 8 3-8217 CLEVIS, Support 9 4-0527 BRACKET, Mounting (Front Tine Tiller Only) 10 1-3460 PIN, Clevis 3/8x1-1/2" (Front Tine Tiller Only) 11 1-3111 PIN, Clevis 1/2x1" (3) 12 1-3844 PIN, Hair (4) 13 9-0497 BOLT, 3/8-16x1-1/2" Carriage (4) 14 9-0122 WASHER, 3/8 Flat (8) 15 9-0390 WASHER, 3/8 Internal-Tooth Lock (4) 16 9-0130 NUT, 3/8-16 Hex (6) 17 9-0542 SCREW, 1/2-13x1-1/4" Square Head Set (8) 18 9-0326 NUT, 1/2-13 Square (8) 19 9-0543 SCREW, 1/2-13x2" Hex Head Cap (2) 20 9-0254 WASHER, 1/2 Split Lock (2) 21 9-0258 NUT, 1/2-13 Hex (2) 22 9-0211 SCREW, 5/16-18x1-1/2" Hex Head Cap (2) 23 9-0196 NUT, 5/16-18 Hex (2) 24 9-0187 WASHER, 5/16 Split Lock (2) 25 9-0188 WASHER, 5/16 Flat (4) 26 9-0134 SCREW, 3/8-16x3/4" Hex Head Cap (2) 27 9-0118 WASHER, 3/8 Split Lock (2) INSTRUCTION 1-5217 (8/85) (OVER) PAGE 2 FIGURE 2: REMOVE HARDWARE INDICATED FIGURE 4: DRAW-BAR TO CLEVIS BRACKET (CONTINUED) ASSEMBLY INSTRUCTIONS: Presassemble kit components in sequence shown but do not attach the clevis bracket (item 2) to the draw-bar (item 7) at this time. This pertains to the set-up only. INSTALLATION INSTRUCTIONS: Stand the tiller on front stand-up bar, remove the drag shield and install the support clevis (item 8) with hardware shown in illustration. STEP 1: Remove the depth bar retaining hardware and the tiller chain case bolt directly below it as shown in figure 1. STEP 2: Attach the clevis bracket (item 2) to the depth bar retainer and chain case using the two 5/16x1-1/2" hex head bolts, lockwashers and hex nuts (items 22, 23 & 24 of illustration. NOTE: Install two of the 5/16 flat washers (item 25) on each side of the chain case to act as spacers as shown in figure 2. The clevis bracket can remain on the tiller permanently! STEP 3: Remove the depth bar handle grip spring then remove the depth bar. Save these parts for use later when the harrow is removed. NOTE: Use mounting bracket (item 9) & clevis pin (item 10) for Front Tine Tillers. Mounting bracket (item 9) & clevis pin (item 10) replace items 2 & 11 on Front Tine Tillers. To mount, reverse skid-arm, and slide mounting bracket on from bottom. STEP 4: Attach the draw-bar of the assembly to the clevis bracket with two clevis pins and lock in place with two hair pins. NOTE: Harrow adapter (item 6) can be reversed to point down for a more shallow furrow. STEP 5: Return the tiller to its wheels. NOTE: To use four shank harrow kit on Front Tine Tiller; Tire Kit # 6-0262 must be used. SNAPPER POWER EQUIPMENT McDonough.GA* 30253 Company 1-5217 (8/85) PRINTED in U.S.A....