Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Bush Hog Dateigröße: 1.8 mb Dateiname: 24b94d07-0bf6-40d0-aa24-0c3a60d5cd09.pdf Unterrichtssprache:

2. Fit the two spacers and the bracket over the outer tube and loosely install the four socket-head screws. 3. Tighten the four socket-head cap screws to secure the cutting attachment shield. 4-6 mm Remove air cleaner coverThrottle lever free play Lock Nut Adjust as required to obtail 4-6 mm free play Cable Adjuster Sub-Shield (when trimmer head is in use) Outer Tube Socket-Head Cap Screws RetainingNut Mounting Plate Spacer Spacer Bracket Cutting Attachment Shield w/subshield Cutting attachment shield assembly CAUTION! Make sure the clamp screw and retaining nut are securely tightened before tightening the four socket- head cap screws. 1. Attach the shield extension to the cutting attachment shield. Cutting Attachment Shield WARNING! NEVER use this machine without sub-shield when using a trimmer head. CAUTION! Make sure the sub-shield is completely hooked at the hook receiver. Hook Receiver Sub-shield Hook WARNING! NEVER operate the unit without the cutting attachment shield installed and tightly secured! Attach the shield extension to the cutting attachment shield Assembly (continued) Hand-tighten Trimmer Head (counterclockwise to install) Installing a Trimmer Head NOTE: Shaft Bolt Bolt Guard Gear Shaft Holder B Holder A 3.Using the hex wrench to secure Holder A, install and hand-tighten the trimmer head (counter-clockwise to install). 4.Remove the hex wrench from the gearcase and holder. Hex Wrench This unit is now completely assembled and ready to use as a trimmer. This unit is shipped with Holder A, Holder B, shaft bolt, and bolt guard installed. The shaft bolt is a LEFTHAND thread. Remove it by turning CLOCKWISE! 1. With the gearcase output shaft facing up, rotate the gearshaft and Holder A until the hole in Holder A aligns with the matching hole in the gearcase flange, and then lock the holder to the gearcase by inserting the long end of the hex wrench through both holes. 2. Using the combination spark plug/ screwdriver wrench, remove the shaft bolt, and bolt guard. (The bolt guard and shaft bolt are not used with a trimmer head). Installing Brushcutter Blade WARNING! Do not attach any blade to a unit without proper installation of all required parts. Failure to use the proper parts can cause the blade to fly off and seriously injure the operator and/or bystanders. 1. Turn the unit upside down so the gear case output shaft is facing UP and remove the shaft bolt, bolt guard and holder B from the gear case shaft. 2. Align the hole in blade holder A with the matching hole in the gear case flange and then temporarily lock the output shaft by inserting a hex wrench through both holes. 3. Fit the blade over the flange on holder A. Shaft Bolt Bolt Guard Holder B Gear Shaft Holder A Hex wrench Temporarily lock the output shaft by inserting a hex wrench through both holes 4. Install blade holder B on the output shaft. Blade OutputShaft Blade Holder B Install blade holder B on the output shaft. WARNING! The blade must fit flat against the holder flange. The blade mounting hole must be centered over the raised boss on blade Holder A. WARNING! Holder B must fit flush against the blade and the splines engaged to the output shaft. Hex Wrench (blade not shown forclarity) (blade not shown forclarity) Assembly (continued) CAUTION! Install the blade so its printed surface is visible to the operator when the brushcutter is in the normal Tighten the assembly operating position. IMPORTANT! Discard blades that are bent, warped, cracked, broken or damaged in any way. Use a sharp blade. A dull blade is more likely to snag and thrust. The unit should now be completely assembled and ready for use with a blade. Install the bolt guard and then the 5. blade retaining bolt. Using the com- bination spark plug wrench/screw- driver, tighten the bolt firmly in a counter-clockwise direction. Remove the hex wrench. 6. Using the combination spark plug wrench/ screwdriver, tighten the bolt firmly in a counter-clockwise direction. Mixing Fuel WARNING! Alternative fuels, such as E15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting Shindaiwa requirements are NOT approved for use in Shindaiwa gasoline engines. Use of alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components. Fuel Requirements Gasoline -Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved. 2 Stroke Mixture Oil - A 2-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345/FD standards must be used. Shindaiwa OneTM 2-Stroke Oil is strongly recommended as it meets this standard and is specifically formulated for use in all Shindai...

Herunterladen

Geben Sie zwei Ziffern: