Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Logan Graphic Products Dateigröße: 1022.68 kb Dateiname: Unterrichtssprache:

Hold the 702 Bevel Cutter upside down in your hand with the blade activated in the cutting position. 2. Measure the exposed amount with a ruler at the same angle as the blade. For standard thickness mat board (4 ply/1.4mm) only 1/8” of blade should be seen (Fig. 24). 3. Turn blade depth screw (clockwise) to decrease blade depth and (counterclockwise) to increase depth. NOTE: Always have blade depth set so that Slip Sheet is only slightly scored. Overcut adjustment 1. Use the marks on the start & stop indicator to reduce or increase overcuts. 2. To reduce overcuts, start & stop like this (Fig. 25). 3. To increase overcuts, start & stop like this (Fig. 26). Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Fig. 24 Fig. 22 Fig. 23 Fig. 26 StartStopFig. 25 847-526-5515 LoganGraphic.com Simplex Classic Mat Cutter Instruction Manual Model 550-1/560-1 7 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com ABChanging Scales Your Logan mat cutter is supplied with a separate set of either inch or metric scales. If you prefer a different form of measurement than what is installed on your mat cutter, use these simple steps to recalibrate your machine to the alternate scale measurements. Switching inch scale to metric scale: Step 1: Using a pencil, mark a small line on the machine next to the 2 3/4” mark of the inch scale (Fig. 27). Mark the line on the machine itself, NOT the scale. Step 2: Carefully peel up and remove the inch scale and clean off any adhesive or glue residue left behind. Step 3: Peel off the adhesive backing from the metric scale and apply it with the 7cm mark exactly next to the pencil mark you drew. Conversion: 2 3/4” = 7cm (Fig. 28). Switching metric scale to inch scale: Step 1: Using a pencil, mark a small line on the machine next to the 7cm mark of the metric scale (Fig. 29). Mark the line on the machine itself, NOT the scale. Step 2: Carefully peel up and remove the metric scale and clean off any adhesive or glue residue left behind. Step 3: Peel off the adhesive backing from the inch scale and apply it with the 2 3/4” mark exactlly next to the pencil mark you drew. Conversion: 7 cm = 2 3/4” (Fig. 30). Re-Squaring the Squaring Arm Tools needed: Screwdriver, Carpenter’s Square Before making any adjustments to the squaring arm, make sure that the machine is truly out of square, not the mat board, by using the squareness test. ATTENTION: It is common for 32” x 40” sheets of mat board to be un-square when bought. Take this into account before making any adjustments to the squaring arm. Squareness Test 1. Place the carpenter’s square against the right hand side of the guide rail and down against the squaring arm (Fig. 31). Lock to see if there are any gaps between the framing square and the squaring arm. If so, the squaring arm needs to be adjusted. To Re-Square 1. By looking at where the gap is, you can determine which way the squaring arm needs to go, in order to be square again. 2. Remove the squaring arm and locate the two screws inside of the slot. 3. To adjust, you must turn screws A & B in equal but opposite directions. To move the far right end of the squaring arm towards the top end of the machine, turn adjustment screw B inward (clockwise) about a quarter turn, and turn adjustment screw A outward (counter-clockwise) a quarter turn (Fig. 32) 4. Re-install the squaring arm and check for square. This is a trial and error method. In some cases more than a quarter turn is needed, in some cases, less. Mat Guide Assembly If mat guide wedge becomes unscrewed from mat guide, reassemble making sure angle of wedge is aligned correctly (Fig. 33). inch scale01234Mark a pencil line on the machine here at 2 3/4” metric scale13572468101291113Apply the metric scale so the 7cm mark aligns with the pencil mark metric scale13572468101291113Mark a pencil line on the machine here at 7cm inch scale01234Apply the inch scale so the 2 3/4” mark aligns with the pencil mark Fig. 27 Fig. 28 Fig. 29 Fig. 30 Mat Guide #602 Slide #603 Wedge #604 Mat Guide Screws (2) #112N Mat Guide Knob Fig. 32 Fig. 31 Fig. 33 Place Square Here Simplex Classic Mat Cutter Instruction Manual Model 550-1/560-1 7 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com ABChanging Scales Your Logan mat cutter is supplied with a separate set of either inch or metric scales. If you prefer a different form of measurement than what is installed on your mat cutter, use these simple steps to recalibrate your machine to the alternate scale measurements. Switching inch scale to metric scale: Step 1: Using a pencil, mark a small line on the machine next to the 2 3/4” mark of the inch scale (Fig. 27). Mark the line on the machine itself, NOT the scale. Step 2: Carefully peel up and remove the inch scale and clean off any adhesive or glue residue left behind. Step 3: Peel off the adhesive backing from the metric scale and apply it with the 7cm mark exactl...

Herunterladen

Geben Sie zwei Ziffern: