Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Logan Graphic Products Dateigröße: 1022.68 kb Dateiname: 550-1.pdf Unterrichtssprache:

Has three separate depth settings. Slip Sheet A Slip Sheet is a piece of scrap mat board that is placed beneath the mat when bevel cutting Left Right Fig. 1 Carton Contents 1. Straight Cutter 2. Bevel Cutter 3. Squaring Arm 4. Squaring Arm Stop 5. Mat Guide 6. Mat Guide Channels (2) 7. Channel Screws (2) 8. Screwdriver 9. Rail Stops 10. Blade Pack 11. DVD Bottom 1 2 3 11 6 7 8 10 9 4 Mat Guide Channel 5 Rail Stop Congratulations on your purchase of the Logan Simplex Classic Mat Cutter. The Simplex Classic is a well-designed mat cutter, combining the best of what Logan mat cutters have to offer. Features like heavy duty pull style bevel cutter with anti-crawl pin, pivot & pull straight cutter, production stops, squaring arm, parallel mat guide, plus the flexibility to add additional accessories like the glass cutter or surface V-groovers make the Simplex Classic a cost effective and useful tool for artists, crafters, photographers and framers. This instruction manual is written to familiarize you with the product. Please take some time to review the instructions before cutting. You will find that the time taken will be well worth it, and you will be cutting professional mats in no time. PRODUCT DESCRIPTION 550-1 / 560-1 Simplex Classic- 40 in vinyl covered cutting board with mat guide in aluminum channels, two production stops, 27 in squaring arm, straight and bevel cutting heads, slip sheet, screwdriver, DVD and one 5-pack of Logan #270 blades. Orientation The procedures detailed in the following instructions refer to the right & left sides and top & bottom of the machine as shown (Fig. 1). Instruction Manual Simplex Classic Mat Cutter Model 550-1/560-1 Blade Installation 1. Loosen blade retaining screw enough to allow blade holder to tilt back (Fig. 2). Loosen the blade holding knob. 2. Remove one blade from the package of five. NOTE: Because the blades are packed with a small amount of oil, they may stick together. Be certain that only one blade is being inserted into the blade slot. 3. Slide blade, sharp edge down, fully into blade holder (Fig. 3). NOTE: The hole in the blade is not designed to line up with the blade screw. 4. Tighten blade screw. 5. Tilt blade holder down, allowing tip of blade to enter into the blade slot and retighten retaining screw (Fig. 4). Blade Installation - Model 701-1 Straight Cutter Elite 1. Remove blade knob and blade cover. 2. Align blade hole over thread. Be sure sharp edge of blade is facing down. 3. Reassemble blade cover and blade knob (Fig. 5). NOTE: Adjust blade to foamboard (fully extended), standard 4-ply mat board (middle setting) or safety (fully retracted). Mat Guide Assembly 1. Press each Mat Guide Channel into board slots with rounded end towards guiderail. (Fig. 6). 2. Insert two channel screws from the UNDERSIDE of board and tighten (Fig. 6). 3. Loosen each mat guide knob three full turns. 4. Hold mat guide at ends with your thumbs on the loosened knobs with raised edge facing guiderail and evenly drop mat guide into channels. 5. Slide to adjust and tighten knobs to lock mat guide (Fig. 7). Fig. 2 Fig. 3 Fig. 4 Fig. 7 Fig. 6 Fig. 5 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com Simplex Instruction Manual Classic Mat Cutter Model 550-1/560-1 4 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com Squaring Arm Assembly 1. Line up squaring arm along side of slot, ensuring the bottom of the v-groove is underneath screw (Fig. 8). 2. Slide into the slot (Fig. 8). 3. Align slots and tighten screw (Fig. 9). 4. Slide stop onto squaring arm (Fig. 10). Straight Cutting Board to Size 1. Remove mat guide and slip sheet. 2. Set squaring arm stop to dimension of cut (Fig. 11). 3. Place mat color side down under guide rail and against squaring bar stop. 4. Set the proper depth setting on the Straight Cutting Head. 5. Hook the Straight Cutting Head onto the Guide rail past the end of the board to be cut. Grasp the handle as shown in the picture, pivot down and pull the Straight Cutting Head towards you. Keep constant downward pressure on the Straight Cutting Head and the Guide Rail as you make your cut (Fig. 12). CAUTION: Be careful to control the Straight Cutting Head as it breaks through the end of the matboard, as it will tend to “jump” towards you. Bevel Cutting Mat Openings, Without Rail Stops, Line to Line EXAMPLE: Cutting a mat with a 2” border. 1. Move stops out of cutting area or remove from rail (Fig. 13). 2. Set the Mat Guide to the desired border width. For example, for a 2” border, align the front of the Mat Guide at the 2” mark and tighten the Black Knobs (Fig. 14). 3. Make sure the Slip Sheet is in place before bevel cutting. You must use a Slip Sheet. The straight cut slot underneath the Guide Rail is for straight cutting only. 4. Place the mat color side down under the Guide Rail and up against the squaring bar and mat guide (Fig. 15). 5. Using a pencil, draw a line d...

Herunterladen

Geben Sie zwei Ziffern: