Stimmen - 5, Durchschnittliche Bewertung: 4 ( )

Hersteller: EarthQuake Dateigröße: 4.34 mb Dateiname: Unterrichtssprache:

Please slit backing material to ensure ease of removal. Colors Used: Pantone Metallic 876 C ARDISAM, INC. 1160 8th Avenue | Cumberland, WI 54829 | USA Serial No. Earthquake 3365CE Year: 2010 Mass: 47.63 kg Max. Operating Speed: 3600 rpm Nominal Power Rating: 5.06 kW LBLINFO3365CE DIELINE SIZE: 70mm x 45mm Part No. LBLINFO3365CE Name Plate Tine Shield Decal OPERATor INSTRUCTIONS and parts Front Tine Models 3365_3365B_3365K_3365KPS_3365CE_3365PS_R3355H_3365PSCE Page GetEarthquake.com 800-345-6007 Unpac king and Assembly unpac k tiller & assemble 1. Open top of carton and remove handlebar assembly. 2. Find parts packet. Parts packet for 3365/3365B/3365K/3365CE contains: 6- 5/16-18 x 1-3/4” bolts 6- 5/16” spring lockwashers 2- hand knobs 4- locknuts 2- 1/2” push nuts 1- detent pin Parts packet for 3365PS/3365KPS/R3365H/3365PSCE contains: 2- 3/8-16 x 1” bolts 2- 3/8-16 biway locknuts 2- 5/16-18 x 1” bolts 4- 5/16-18 x 1-3/4” bolts 6- 5/16” spring lockwashers 2- hand knobs 4- 5/16” locknuts 2- 1/2” push nuts 1- detent pin 3. Cut open end of carton and remove machine: a. Install wheels on each end of axle; tap on push nuts with a hammer. b. Assemble tines to unit, inside tines first. Sharp edge of tine will be away from operator at top, or face down at front of machine. c. Outside tines have two positions- wide 21” and narrow 16”. For narrow width, assemble with short side of tine holder pipe towards center of machine. d. For wide width, move the left tine to the right side and right tine to the left side. Assemble with the long half of tine pipe towards machine. e. Slide the top handle of handlebar over the lower loop. Put 5/16-18 x 1-3/4” bolts through both holes from inside out; put on 5/16” spring lockwashers and tighten with hand knobs. Models 3365PS, 3365KPS, and R3365H will use 3/8-16 x 1” bolts with nuts and 5/16-18 x 1” bolts with hand knobs. See parts explosion on page 19. f. Check upper and lower jam nuts for tightness. See page 9, Belt Tension Adjustment. g. Add and check engine oil. install depth regulator lever 1. Install the depth regulator lever through hole in bracket from the bottom up with curve to rear of unit and secure with detent pin. Fill engine CRANKCASE 1. Add oil according to engine manual. Do not overfill. Use a clean, high quality detergent oil. Container must be marked A.P.I. Service SF - SJ. Use no special additives with recommended oils. Do not mix oil with gasoline. Oil level must be full. Check the oil level by removing oil fill plug. Oil level should be up to the bottom of the fill plug opening. 2. Always check oil level before starting engine. Refer to engine manual for capacity and type of oil to use. upper handlebar ! CAUTION DO NOT TRY TO LIFT THE ROTOTILLER FROM THE CARTON. IMPORTANT The rig ht an d left si des of your rototiller are determine d from the operating position as you face the direction of forwar d travel. Engine is shipped from factory wit hout oil . You must add engine oil before starting engine. narrow tine width wide tine width lower handlebar loop hand knob depth regulator lever detent pin Page GetEarthquake.com 800-345-6007 OPERATor INSTRUCTIONS and parts Front Tine Models 3365_3365B_3365K_3365KPS_3365CE_3365PS_R3355H_3365PSCE Features (3365/3365B/3365Ce/3365K) The advantage of the EARTHQUAKE® BADGER™ gear drive rototiller over other front tine tillers is the exclusive unfolding and flexible drag bar. This gives the Earthquake® Badger™ gear drive tiller its stability and versatility. For easy transport, fold the wheels under the engine. During operation, the wheels unfold back and the drag bar folds down. The long length between the tines and the drag bar make this the most comfortable front tine tiller on the market. drive safety control lever 3-way adjustable tine widths forward cable front belt cover hand knob Transport Position Operating Position OPERATOR INSTRUCTIONS ANd PARTS Front Tine Models 3365_3365B_3365K_3365KPS_3365CE_3365PS_R3355H_3365PSCE CONTROLS dRIvE SAFETY CONTROL LEvER Engages tines into forward; releasing returns machine to neutral. Pulling down on the drive safety control lever engages the tines. Releasing the drive safety control lever disengages the tines to a neutral position. BELT TENSION AdjUSTMENT Proper belt tension is critical to good performance. After 30 minutes of operation, all cables may have to be adjusted due to initial stretch. Thereafter, check tension after every two hours of operation. To increase belt tension: 1. Loosen upper jam nut. Turn nut up cable in 1/8” increments. 2. Tighten lower jam nut. 3. Check adjustment. This procedure can be repeated until conduit adjustment bolts have no more adjustment left. If no more adjustment can be made, belt may have to be replaced. dEPTh REGULATOR LEvER Tilling depth is controlled by the height of the depth regulator lever. To adjust tilling depth: 1. Remove detent pin. 2. Raise the depth regulator lever to position tines at chosen tilling depth. 3. Align hole in depth regula...

Herunterladen

Geben Sie zwei Ziffern: