Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Maxim Dateigröße: 1.09 mb Dateiname: Unterrichtssprache:

Spring 625 461469 1 Depth Bar Adjust. Pin 705 359321 1 Idler Pulley 338009 1 Idler Pulley 706 162069 1 Idler Shaft 708 359325 1 Idler Shaft Arm 709 400290 1 Capscrew NC, 3/8” x 1 3/4” 802 359330 2 Wheel Shoulder Bolt 804 400184 2 Cap Screw, NC 5/16” x 3/4” 805 400186 1 Cap Screw, NC 5/16” x 1” 400190 Cap Screw, NC 5/16” x 1 1/4” 806 400197 1 Cap Screw, NC 5/16” x 2 1/4” 807 400200 4 Cap Screw, NC 5/16” x 2 1/2” 809 400207 2 Cap Screw, NC 5/16” x 3 3/4” 811 400275 1 Cap Screw, NC 3/8” x 3” 813 400115 5 Cap Screw, NC 1/4” x 1 1/2” 814 400109 1 Cap Screw, NC 1/4” x 1 3/4” 816 443101 6 Nut, NC 1/4” 817 443106 11 Nut, 5/16” 818 443110 2 Nut NC, 3/8” 819 444721 4 Locknut NC, 3/8” 820 444720 1 Locknut NF, 3/8” 821 446130 6 Lockwasher, 1/4” 822 446136 11 Lockwasher, 5/16” 825 455050 1 Washer SAE Flat, 1/2” 830 162096 Optional LH Tine Shield 831 162095 Optional RH Tine Shield 833 359853 1 Engine Guard 13 4 OPERATION BEFORE USING THIS MACHINE CHECK THE ASSEMBLY INCLUDING THE HANDLE AND CONTROLS. MAKE SURE ALL FASTENERS ARE TIGHT. MAKE SURE THE THROTTLE AND OTHER CONTROLS WORK CORRECTLY. BEFORE STARTING THIS TILLER, BE FAMILIAR WITH ALL OPERATING CONTROLS. KNOW HOW TO DISENGAGE TINES, STOP FORWARD MOVEMENT AND SHUT OFF ENGINE. FRAME ASSEMBLY OPERATING CONTROLS Throttle Control Lever The throttle control lever, located on the left side of the handle controls engine speed. When starting, place control lever in center position. Then adjust to desired speed. To stop engine move throttle control lever to rear position. Push stop switch at spark plug. Clutch Lever The clutch is disengaged when clutch is away from handle grip. To engage clutch, squeeze clutch lever to handle. Operating Instructions Before operating the machine, become familiar with the operating instructions and safety suggestions in this manual. Operate the machine in an open area to get the “feel” of the machine and its controls. Starting and Stopping the Engine Before starting the engine check that all bolts are tight, and that the tiller is assembled properly. Review Safety suggestions and Operating Instructions for safe and proper use of the tiller. Pre Start 1. Check the spark plug for proper connection on the spark plug. 2. Fill the fuel tank with clean, fresh, regular gasoline from an approved container. 3. Check the oil for proper level. Refer to engine owner’s manual for correct grade and quantity and directions. 4. Make certain clutch lever is in disengaged position. Starting Procedure 1. Move throttle control lever to center position. 2. Manually open choke. Hold the handle with your left hand while pulling the starter rope with your right. Pull the rope out slowly until the engine reaches the start of the compression cycle (the rope will pull slightly harder at this point). Then allow the rope to retract fully. 3. Pull the rope with a continuous full arm stroke. Keep a firm grip on the starter handle and let the rope rewind slowly. Do not let the handle snap back against the starter. ...

Herunterladen

Geben Sie zwei Ziffern: