Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Honda Automobiles Dateigröße: 1.55 mb Dateiname: Unterrichtssprache:

Avoid getting dirt or water in the fuel tank. Occasionally you may hear light “spark knock’ or “pinging” (metallic rapping noise) while operating under heavy loads. This is no cause for concern. Ifspark knockor pinging occurs at a normal load, steady engine speed, under changebrands of gasoline. If spark knock or pinging persists, seean authorized Honda servicing dealer. I NOTICE I Running the engine with persistent spark knock or pinging can cause engine damage. Running the engine with persistent spark knock or pinging is misuse, and the Distributor’s Limited Warrantydoes not cover parts damaged by misuse. SERVICING YOUR HONDATILLER ENGINE OIL LEVEL CHECK Check the engine oil level with the tiller on a level surface and the engine stopped. 1. Remove the oil filler cap/dipstick and wipe it clean. 2. Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick. 3. If the oil level is low, fill to the top of the oil filler neck with the recommended oil (see page 31). 4. Screw in the filler cap/dipstick securely. OIL FILLER CAPlDlPSTlCK NECK tl+ LOWER LlMT SERVICING YOUR HONDA TILLER ENGINE OIL CHANGE Drain the oil while the engine is warm to assure rapid and complete draining. 1. Place a suitable container below the engine to catch the used oil, then remove the filler cap/dipstick, drain plug and sealing washer. 2. Allow the used oil to drain completely, then reinstall the drain plug and sealing washer. Tighten the plug securely. lxEia Improper disposal of engineoil can be harmful to the environment. If you change your own oil, please disposeof the used oil properly. Put it ina sealed container it a recycling center.Donot discard ita trash and take to in bin or dump it on the ground. 3. With the tiller in a level position, fill to the outer edge of the oil filler hole with the recommended oil (see page29). Oil Capacity: 0.61 USqt (0.58 4) Running the engine witha low oil level can cause engine damage. 4. Screw in the filler cap securely. OIL FILLER CAP/DIPSTICK NECK 11 UPPER LlMT - -1 DRAIN r-y LOWER LlMT SERVICING YOUR HONDA TILLER ENGINE OIL RECOMMENDATIONS Oil is a major factor affecting performance and service life. Use a 4-stroke automotive detergent oil. SAE 1OW-30 is recommended for general use. Other viscosities shown in the ’ chart may be used when the average temperature in your area is within the recommended range. SAE VISCOSITY GRADES -20 0 20 40 60 80 100 ‘F I I -30 -20 -10 0 10 20 30 40 ‘C AMBIENTTEMPERATURE The SAE oil viscosit! and service classification are in the API label on the oil container. Honda recommends that you use API SERVICE category SJ oil. 31 SERVICINGYOUR HONDATILLER TRANSMISSION OIL LEVEL CHECK Check the transmission oil level with the tiller ona level surface and the engine stopped. 1. Remove the transmission oil filler cap. The oil should be level with the lower edge of the oil filler hole. 2. Add the same oil as recommended for the engine (see page 31),if the level < is low. 3. Screw in the filler cap securely. ,$ TRANSMISSION OIL FILLER CAP .-- OIL FILLER HOLE LOWER EDGE OF THE OIL FILLER HOLE SERVICING YOUR HONDA TILLER AIR FILTER INSPECTION Press the latch tabs on the fuel tank side of the air cleaner cover, removethe air cleaner cover, and remove the filter. Check the filter to be sure it is clean and in good condition. If the filter is dirty, remove the filter and clean it as described on page34. Replace the filterif it ' is damaged. Reinstall the filter and air cleaner cover.Make sure the latch tabs aresecured. Operating the engine without an airor with a damaged air filter, will allow filter, dirt to enter the engine, causing rapid engine wear. of damage is not This type covered by the Distributor's Limited Warranty. eAIR CLEANER COVER LATCH TABS / TABS AIR FILTER 33 SERVICING YOUR HONDATILLER AIR FILTER CLEANING A dirty air filter will restrict air flow to the carburetor, reducing engine performance. If you operate the engine in very dusty areas, clean the air filter more frequently than specified in the Maintenance Schedule. 1. Tap the air filter element several times on a hard surface to remove dirt, or blow compressed air [not exceeding 30 psi (207kPa, 2.1 kgf/cm2)] through the air filter from the air cleaner housing side. Never try to brush off dirt; brushing will force dirt into the fibers. Replace the air filter if it is excessively dirty. 2. Wipe dirt from the air cleaner housing and cover using a moist rag. Be careful to prevent dirt from entering the air duct that leads to the carburetor. SERVICING YOUR HONDA TILLER SPARK PLUG SERVICE Recommended spark plug: BPR6ES (NGK) Incorrect spark plugs can cause engine damage. 1. Disconnect the spark plug cap, and remove anydirt from around the spark plug area. 2. Remove the spark plug with a 13/16-inch spark plug wrench. PULG WRENCH I' \-1 If / 3. Inspect the spark plug. Replace it if the electrodes are worn,or if theinsulator (0.70 -0.80 mm) is cracked or chippe...

Herunterladen

Geben Sie zwei Ziffern: