Stimmen - 5, Durchschnittliche Bewertung: 4 ( )

Hersteller: Tanaka Dateigröße: 390.67 kb Dateiname: Unterrichtssprache:

s Man s Mans Mans Mans Mans Man ual ualualualualual Model Numbers: TPE-2501,TPE-2510 TPE-2501,TPE-2510TPE-2501,TPE-2510TPE-2501,TPE-2510TPE-2501,TPE-2510TPE-2501,TPE-2510 TPE-250PF TPE-250PFTPE-250PFTPE-250PFTPE-250PFTPE-250PF ,TPE-270PF/PN ,TPE-270PF/PN,TPE-270PF/PN,TPE-270PF/PN,TPE-270PF/PN,TPE-270PF/PN POLE EDGERS POLE EDGERSPOLE EDGERSPOLE EDGERSPOLE EDGERSPOLE EDGERS P/N 28575 Date 02-27-01 TPE-2510 TPE-270PF Supplier ToThe Outdoor Power Equipment Industry ISM, Inc. . 1028 4th Street SW . Auburn, WA 98001 . Phone: (253) 333-1200 . Fax: (253) 333-1212 custsvc@tanaka-ism.com Owner.s ManualTPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF Before using this unit: • Read the operator.s manual carefully. • Check that the cutting equipment is correctly assembled and adjusted. • Start the unit and check the carburetor adjustment. See .Maintenance.. WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Always wear eye, head and ear Read, understand and follow all It is important that you read, fully understand and protectors when using this unit. warnings and instructions in this observe the following safety precautions and manual and on the unit. warnings. Careless or improper use of the unit may cause serious or fatal injury. Keep all children, bystanders and helpers 15m (50ft.) away from the unit. If anyone approaches you, stop the engine and cutting attachment immediately. 1 custsvc@tanaka-ism.com Owner.s ManualTPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF 1. What is What? Since this manual covers several models, there may be some difference between pictures and your unit. Use the instructions that apply to your unit. 1. Fuel Cap 2. Throttle Trigger 3. Starter Handle 4. Blade guard 5. Blade 6. Drive shaft pipe 7. Loop handle 8. Spark plug 9. Ignition Switch 10. Depth guide wheel 11. Lock Button 12. Knob nut 13. Choke lever 2 custsvc@tanaka-ism.com Owner.s ManualTPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF 2. Warnings and safety instructions Operator safety • Always wear a safety face shield or goggles. • Always wear heavy, long pants, boots and gloves. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair so it is above shoulder length. • Do not operate that tool when you are tired, ill or under the influence of alcohol, drugs or medication. • Never let a child or inexperienced person operate the machine. • Wear hearing protection. • Never start or run the engine inside a closed room or building. Breathing exhaust fumes can kill. • Keep handles free of oil and fuel. • Keep hands away from cutting equipment. • Do not grab or hold the unit by the cutting equipment. • When the unit is turned off, make sure the cutting attachment has stopped before the unit is set down. • When operation is prolonged, take a break from time to time so that you may avoid possible white finger disease which is caused by vibration. Tool safety • Inspect the entire tool before each use. Replace damaged parts. Check for fuel leaks and make sure all fasteners are in place and securely fastened. • Replace parts that are cracked, chipped or damaged in any way before using the tool. • Make sure the safety guard is properly attached. • Keep others away when making carburetor adjustments. • Use only accessories as recommended for this tools by the manufacturer. WARNING! Never modify the tool in any way. Do not use your cutting tool for any job except that for which it is intended. Fuel safety NOTE! • Empty the fuel tank before storing the tool. Especially, in case of over three month storage, it is a must otherwise fuel may corrode causing carburetor damage. It is recommended that the fuel be emptied after each use. If fuel is left in the tank, store so fuel will not leak. • Mix and pour fuel outdoors and where there are no sparks or flames. • Use a container approved for fuel. • Do not smoke or allow smoking near fuel or the tool or while using the tool. • Wipe up all fuel spills before starting engine. • Move at least 3 m (10ft.) away from fueling site before starting engine. • Stop engine before removing fuel cap. • Empty the fuel tank before storing the tool. It is recommended that the fuel be emptied after each use. If fuel is left in the tank, store so fuel will not leak. • Store tool and fuel in area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. WARNING! Anti-vibration systems do not guarantee that you will not sustain white finger disease or carpel tunnel syndrome. Therefore, continual and regular users should monitor closely the condition of their hands and fingers. If any of the above symptoms appear, seek medical advice immediately. Cutting safety • Inspect ...

Herunterladen

Geben Sie zwei Ziffern: