Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Bolens Dateigröße: 14.63 mb Dateiname: Unterrichtssprache:

The safety decal locations are shown (at a reduced size) below. There are other decals located on your equipment for operation and controls identification. They are also shown below and in your Parts Catalog. If you need a replacement decal, please refer to the Parts Catalog that accompanied this Manual. Decal Locations A) WARNING: Hot Surfaces decal. On 8HP Kohler engines (shown), located on top of the engine. On Briggs & Stratton engines (not shown), located on top of the muffler guard. F) Engine Stabilization decal. On 8HP Kohler engines (shown), located on top of the engine. On Briggs & Stratton engines (not shown), located on the top, front of the engine cover. C) WARNING: Operating Instructions decal. Five groups of safety statements are provided along with tiller operating instructions. E) Forward Interlock Lever decals (2). B) WARNING: Engine Ignition. Provides safety and operational information for using the Keyswitch Ignition. On electric start models only. D) Power Unit Operating instructions decal. iiM' Subjects covered in this Section: • Inspection After Delivery • Unpacking and Checking Contents • Attach the Handlebars • Remove Tiller from Shipping Platform • Connect Forward Interlock Wire Harness • Attach Wheels/Tines/PTO Drive Lever • Check Gear Oil Levels in Power Unit and Tine Attachment Transmissions • Add Motor Oil to Tiller Engine • Attach Engine Throttle Lever to Handlebar • Adjust the Air Pressure in the Tires • Assembling the Electric Start System Section m Assc Please carefjlly follow tne steps in t'lis Sect'or to properiv assemble yo-r new machira These steps will not tase very long and tney wi I assure you o' navmg assem bled your machine correctly. A WARNING To prevent personal injury or property damage, do not start the engine until all assembly steps are complete and you have read and understand the safety and operating instructions in this Manual. Tools Needed: 0"c 3/8 Open End or Adjustable Wrencn One 9/16 Open End or Adjustab.e Wrench One 3/■! Open End or Ad)UStabie Wrench Two 7/16 Open Ena or Adjustab e Wrenches Two 1/2" Open End or Adjustable Wrenches One Flat Blaae Screwdriver Scissors (to trim plastic ties) Quality Vlotar Oil (reie- to the Engine Owner Manual provided with your unit for rrotorail saecifica-tions and capacities) Tire Pressure Gajgc A strong t .¡-'high prop (a wood dox a brick or ooaros^ Inspection After Delivery Inspect your machine immediately after it has been delivered. Make sure that neither the carton nor the contents have been damaged. If you find or suspect any damage, contact the carrier (trucking company) right away. Inform them of the specific damage and that you wish to file a claim. To protect your rights, be sure to put this in writing to the carrier within 15 days after your machine arrives. The carrier will let you know how to proceed with your claim. Please let us know if you need any assistance with this matter. IMPORTANT: Motor oil must be added to the engine before it is started. The procedure for adding oil is explained later on in these assembly instructions. STEM: Unpacking Contents If you haven’t done so, unpack and check the loose parts as listed in the table on page 10. Contact us if any parts are missing. A. Remove the handlebars and the Wheels/Tines/PTO Drive Lever (Items 1 and 2 in Photo 2-1). You may need to cut a plastic tie to free the handlebars from its shipping location. Set them on a clean surface. Do not get dirt on the wire harness plug located at the bottom of the handlebars! B. Remove the loose parts from the plastic envelope that contained these instructions (Items 3 through 8 in Photo 2-2). C. If you ordered an Electric Start Tiller, take out the items from a sealed plastic hardware package under the battery clamp (Items 9 through 11 in Photo 2-3). Your ignition keys are in the keyswitch. 9 Assembly 2- Wheels/Tines/ PTO Drive Lever Wire Harness Plug Photo 2-1. Put Handlebars (Item #1) and Wheels/Tines/PTO Lever (Item #2) aside. 1 2— - Use This Ruler to Check the Hardware Lengths ■ ■ ■ - ......— .............................................. Table 1 - Carton Contents Parts List KEY QTY DESCRIPTION FOR MODEL: 7HP 7HP 8HP 8HP Std. Elec. Std. Elec. Photo 2-1: 1 1 Handlebars............................................... • • • • 2 1 Wheels/Tines/PTO Drive Lever................. • • • • Photo 2-2: 3 1 Clutch Pawl Spring................................... • • • • 4 1 Beit Adjusting Tool.................................... • • • • 5 2 Plastic Cable Ties...................................... • • • • 6 1 Curved Head Bolt, 1/4"-20 x 2“ (Grade 5).. • • • • 7 1 Flanged Lock Nut, 1/4"-20........................ • • • • 8 1 Panhead Screw, #20 -24 x 1/2"................ • • « • Photo 2-3: 9 2 Nuts, 1/4“-20, for battery terminals.......... • • 10 2 Bolts, 1/4"-20 x 5/8", for battery terminals • Ф 11 1 Battery Vent Tube....

Herunterladen

Geben Sie zwei Ziffern: